[OpenWrt Wiki] ASUS Lyra (MAP-AC2200) (2024)

Note: Reset router to factory defaults if it has been previously configured. Installing OpenWrt on this device requires a two-step process, first writing the initramfs image from the OEM firmware - and then finalizing the installation by sysupgrading the real device firmware.

1. Enable ssh in the OEM firmware (use port 22).

2. Copy openwrt-ipq40xx-generic-asus_map-ac2200-initramfs-fit-uImage.itb via scp to /tmp/

3. mtd-write -d linux -i /tmp/openwrt-ipq40xx-generic-asus_map-ac2200-initramfs-fit-uImage.itb

4. reboot -f

5. Now use the Ethernet port right beside the power connector.

6. When booting, the LED will breathe in multiple colors, then blink blue, and when ready, will have a steady blue color.

7. Wait for it to reboot. It will now have the IP 192.168.1.1, and the login will be root without a password.

8. Copy openwrt-ipq40xx-generic-asus_map-ac2200-squashfs-sysupgrade.bin via scp to /tmp/

9. sysupgrade -n /tmp/openwrt-ipq40xx-generic-asus_map-ac2200-squashfs-sysupgrade.bin

   See Also

   About UA Little Rock - University of Arkansas at Little Rock[PDF] HOMECOMING FOR ALUMNI AND FRIENDS OF FORT HAYS STATE UNIVERSITY 2010 - Free Download PDF

10. Wait for it to reboot

11. ssh to 192.168.1.1 and set a root password, or browse to http://192.168.1.1 if LuCI is installed.

→ generic.flashing.tftp

The Asus MAP-AC2200 doesn't have a reliable push-button tftp recovery, as it can't deal with changed UBI partitioning (OEM and OpenWrt differ in this regard). Recovering the MAP-AC2200 requires opening the device and attaching a serial console to the unpopulated header “J35” (2mm spacing), the pinout is: 3.3v - RX - TX - GND (square is VCC).

Prepare your tftp server (192.168.1.70) and provide “asus_map-ac2200-initramfs-fit-uImage.itb” as “HIVESPOT.trx” to the MAP-AC2200.

Interrupt u-boot at the boot screen, pressing “1”, if you followed the default settings below, you can keep the defaults (press [ENTER]):

Please choose the operation: 1: Load System code to SDRAM via TFTP. 2: Load System code then write to Flash via TFTP. 3: Boot System code via Flash (default). 4: Entr boot command line interface. 7: Load Boot Loader code then write to Flash via Serial. 9: Load Boot Loader code then write to Flash via TFTP.You choosed 1 1: Load System code to SDRAM via TFTP. Please Input new ones /or Ctrl-C to discardInput device IP (192.168.1.1) ==:Input server IP (192.168.1.70) ==:Input Linux Kernel filename (HIVESPOT.trx) ==:

Once the initramfs image has booted, sysupgrade can be used to install a known-working sysupgrade image of OpenWrt from the login shell provided on the serial console.

→ hardware.button on howto use and configure the hardware button(s).Here, we merely name the buttons, so we can use them in the above Howto.

Front:

Sides:

Bottom label:

Note: This will void your warranty!

• Peel off four (4) of the five (5) rubber feet (the one at the top may remain)

• then remove four (4) Torx T10 screws.

• Open the case with a spudger – there are latches spread around, but they probably won't break the first time you pop the lid off.

Main PCB:

→ port.serial general information about the serial port, serial port cable, etc.

How to connect to the Serial Port of this specific device:

→ port.jtag general information about the JTAG port, JTAG cable, etc.

How to connect to the JTAG Port of this specific device:
Insert photo of PCB with markings for JTAG port

Booting Linux on physical CPU 0x0Linux version 3.14.77 (jenkins@asuswrt-build-server) (gcc version 4.6.3 20120201 (prerelease) (Linaro GCC 4.6-2012.02) ) #1 SMP PREEMPT Fri Nov 8 23:00:56 CST 2019CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387dCPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cacheMachine model: ASUS. MAP-AC2200Memory policy: Data cache writeallocOn node 0 totalpages: 65024free_area_init_node: node 0, pgdat c07890c0, node_mem_map cfdfa000 Normal zone: 512 pages used for memmap Normal zone: 0 pages reserved Normal zone: 65024 pages, LIFO batch:15PERCPU: Embedded 8 pages/cpu @cfdc8000 s8576 r8192 d16000 u32768pcpu-alloc: s8576 r8192 d16000 u32768 alloc=8*4096pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 Built 1 zonelists in Zone order, mobility grouping on. Total pages: 64512Kernel command line: root_rfs=0x0021b580 flash_type=nand ubi.mtd=UBI_DEV clk_ignore_unusedPID hash table entries: 1024 (order: 0, 4096 bytes)Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)Memory: 251232K/260096K available (4212K kernel code, 197K rwdata, 1184K rodata, 176K init, 537K bss, 8864K reserved, 0K highmem)Virtual kernel memory layout: vector : 0xffff0000 - 0xffff1000 ( 4 kB) fixmap : 0xfff00000 - 0xfffe0000 ( 896 kB) vmalloc : 0xd0800000 - 0xff000000 ( 744 MB) lowmem : 0xc0000000 - 0xd0000000 ( 256 MB) pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB) modules : 0xbf000000 - 0xbfe00000 ( 14 MB) .text : 0xc0208000 - 0xc074d3bc (5397 kB) .init : 0xc074e000 - 0xc077a180 ( 177 kB) .data : 0xc077c000 - 0xc07ad420 ( 198 kB) .bss : 0xc07ad420 - 0xc0833930 ( 538 kB)SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1_ Reboot message ... _______________________________________________________>>> Emergency Sync complete>>> br0: port 4(ath2) entered disabled state>>> br0: port 3(ath1) entered disabled state>>> br0: port 2(ath0) entered disabled state>>> br0: port 1(eth1) entered disabled state>>> device eth1 left promiscuous mode>>> br0: port 1(eth1) entered disabled state>>> device ath0 left promiscuous mode>>> br0: port 2(ath0) entered disabled state>>> device ath1 left promiscuous mode>>> br0: port 3(ath1) entered disabled state>>> device ath2 left promiscuous mode>>> br0: port 4(ath2) entered disabled state>>> STOPPED EVENT for vap 0 (ce370000)>>> OL vap_start +>>> VDEV START>>> OL vap_start ->>> ol_vdev_start_resp_ev for vap 0 (ce370000)>>> su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1>>> send_vdev_up_cmd_non_tlv for vap 0>>> Beacon mode set to staggered. Cannot enable FD>>> __ieee80211_smart_ant_init: Smart Antenna functions are not registered !!! >>> ol_ath_vap_set_param: Now supported MGMT RATE is 1000(kbps) and rate code: 0x43>>> STOPPED EVENT for vap 0 (ce370000)>>> [wifi0] FWLOG: [9236246] WAL_DBGID_SECURITY_MCAST_KEY_SET ( 0x1 )>>> [wifi0] FWLOG: [9236246] WAL_DBGID_SECURITY_MCAST_KEY_SET ( 0x2 )>>> [wifi0] FWLOG: [9236248] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 )>>> [wifi0] FWLOG: [9236248] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 )>>> [wifi0] FWLOG: [9236278] vap-0 VDEV_MGR_VDEV_START ( 0x985, 0x2, 0x0, 0x0 )>>> [wifi0] FWLOG: [9236278] VDEV_MGR_VDEV_START_RESP ( 0x0 )>>> [wifi0] FWLOG: [9236279] VDEV_MGR_HP_START_TIME ( 0x0, 0x985, 0x16f79001 )>>> [wifi0] FWLOG: [9236279] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x1 )>>> [wifi0] FWLOG: [9236279] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 )>>> [wifi0] FWLOG: [9236279] VDEV_MGR_AP_TBTT_CONFIG ( 0x0, 0x985, 0x0, 0x0 )>>> [wifi0] FWLOG: [9236462] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 )>>> [wifi0] FWLOG: [9236462] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 )>>> [UNSPECIFIED] ol_scan_unregister_event_handler: Failed to unregister evhandler=bf61d934 arg=cec184c0>>> >>> [UNSPECIFIED] ol_scan_unregister_event_handler: Failed to unregister evhandler=bf61d934 arg=cec184c0>>> >>> [UNSPECIFIED] ol_scan_unregister_event_handler: Failed to unregister evhandler=bf61df00 arg=cec184c0>>> >>> send_vdev_delete_cmd_non_tlv for vap 0>>> ol_ath_vap_delete: wmi_unified_vdev_delete_send done ID = 0 vap (cb1e0000) VAP Addr = 10:7b:44:XX:XX:XX:>>> ieee80211_mbo_vdetach: MBO terminated>>> ieee80211_oce_vdetach: OCE terminated>>> Suspending Target scn=cdec04c0>>> waiting for target paused event from target >>> ol_ath_thermal_mitigation_detach: ++>>> ol_ath_thermal_mitigation_detach: -->>> ol_if_dfs_clist_update: called, cmd=1, nollist= (null), nentries=0>>> ce_h2t_tx_ce_cleanup 1039 Fastpath mode ON, Cleaning up HTT Tx CEsmart_log_deinit: Smart logging Disabled>>> ol_tx_me_exit: Already Disabled !!!>>> Reset complete for wifi core id : 0>>> hif_disable: Xhif_napi_destroy: NAPI 6 destroyed>>> hif_napi_destroy: no NAPI instances. Zapped.ath_sysfs_diag_fini: diag_fsattr >>> STOPPED EVENT for vap 0 (cd4ce000)>>> OL vap_start +>>> VDEV START>>> OL vap_start ->>> ol_vdev_start_resp_ev for vap 0 (cd4ce000)>>> ol_if_dfs_configure: called>>> ol_if_dfs_configure: ETSI domain>>> ol_if_dfs_disable: called>>> ol_if_dfs_enable: called>>> ol_ath_vap_set_param: Now supported MGMT RATE is 6000(kbps) and rate code: 0x3>>> STOPPED EVENT for vap 0 (cd4ce000)>>> [UNSPECIFIED] ol_scan_unregister_event_handler: Failed to unregister evhandler=bf61d934 arg=cb15a4c0>>> >>> [UNSPECIFIED] ol_scan_unregister_event_handler: Failed to unregister evhandler=bf61d934 arg=cb15a4c0>>> >>> [UNSPECIFIED] ol_scan_unregister_event_handler: Failed to unregister evhandler=bf61df00 arg=cb15a4c0>>> >>> send_vdev_delete_cmd_non_tlv for vap 0>>> ol_ath_vap_delete: wmi_unified_vdev_delete_send done ID = 0 vap (cdf28000) VAP Addr = 10:7b:44:XX:XX:XX:>>> ieee80211_mbo_vdetach: MBO terminated>>> ieee80211_oce_vdetach: OCE terminated>>> Suspending Target scn=cd2c04c0>>> waiting for target paused event from target >>> ol_ath_thermal_mitigation_detach: ++>>> ol_ath_thermal_mitigation_detach: -->>> ol_if_dfs_clist_update: called, cmd=1, nollist= (null), nentries=0>>> ce_h2t_tx_ce_cleanup 1039 Fastpath mode ON, Cleaning up HTT Tx CEsmart_log_deinit: Smart logging Disabled>>> ol_tx_me_exit: Already Disabled !!!>>> Reset complete for wifi core id : 1>>> hif_disable: Xhif_napi_destroy: NAPI 6 destroyed>>> hif_napi_destroy: no NAPI instances. Zapped.ath_sysfs_diag_fini: diag_fsattr >>> channel is not 2.4G return faile.>>> STOPPED EVENT for vap 0 (ccb5c000)>>> OL vap_start +>>> VDEV START>>> OL vap_start ->>> ol_vdev_start_resp_ev for vap 0 (ccb5c000)>>> ol_if_dfs_configure: called>>> ol_if_dfs_configure: ETSI domain>>> ol_if_dfs_disable: called>>> ol_if_dfs_enable: called>>> ol_ath_vap_set_param: Now supported MGMT RATE is 6000(kbps) and rate code: 0x3>>> STOPPED EVENT for vap 0 (ccb5c000)>>> [UNSPECIFIED] ol_scan_unregister_event_handler: Failed to unregister evhandler=bf61d934 arg=cf3ea4c0>>> >>> [UNSPECIFIED] ol_scan_unregister_event_handler: Failed to unregister evhandler=bf61d934 arg=cf3ea4c0>>> >>> [UNSPECIFIED] ol_scan_unregister_event_handler: Failed to unregister evhandler=bf61df00 arg=cf3ea4c0>>> >>> send_vdev_delete_cmd_non_tlv for vap 0>>> ol_ath_vap_delete: wmi_unified_vdev_delete_send done ID = 0 vap (cb1d0000) VAP Addr = 10:7b:44:XX:XX:XX:>>> ieee80211_mbo_vdetach: MBO terminated>>> ieee80211_oce_vdetach: OCE terminated>>> Suspending Target scn=cc0c04c0>>> waiting for target paused event from target >>> ol_ath_thermal_mitigation_detach: ++>>> ol_ath_thermal_mitigation_detach: -->>> ol_if_dfs_clist_update: called, cmd=1, nollist= (null), nentries=0>>> ce_h2t_tx_ce_cleanup 1039 Fastpath mode ON, Cleaning up HTT Tx CEsmart_log_deinit: Smart logging Disabled>>> ol_tx_me_exit: Already Disabled !!!>>> hif_pci_device_reset: Reset Devicehif_pci_disable_bus: Xhif_disable: Xhif_napi_destroy: NAPI 6 destroyed>>> hif_napi_destroy: no NAPI instances. Zapped.ath_sysfs_diag_fini: diag_fsattr >>> channel is not 2.4G return faile.>>> osif_wrap_devt_detach:422 osif wrap dev table detached>>> osif_wrap_detach:475 osif wrap detached>>> ath_lowi_if_netlink_delete Going to decrement current LOWI netlink ref count: 3>>> ol_if_dfs_teardown: called >>> ol_if_dfs_clist_update: called, cmd=1, nollist= (null), nentries=0>>> ol_ath_phyerr_detach: called>>> channel is not 2.4G return faile.>>> ieee80211_bsteering_detach: Band steering terminated>>> ieee80211_ifdetach: ATF terminated>>> Green-AP : Green-AP : Detached>>> >>> Green-AP : Detached>>> ol_if_spectral_detach>>> SPECTRAL : Module removed (spectral = cc3dc000)>>> ol_ath_detach: remove global_ic[2]..gloabl_ic ptr:bf6a1df8>>> ol_ath_detach: Peer Count 531 >>> ath_pci_remove>>> osif_wrap_devt_detach:422 osif wrap dev table detached>>> osif_wrap_detach:475 osif wrap detached>>> ath_lowi_if_netlink_delete Going to decrement current LOWI netlink ref count: 2>>> ol_if_dfs_teardown: called >>> ol_if_dfs_clist_update: called, cmd=1, nollist= (null), nentries=0>>> ol_ath_phyerr_detach: called>>> channel is not 2.4G return faile.>>> ieee80211_bsteering_detach: Band steering terminated>>> ieee80211_ifdetach: ATF terminated>>> Green-AP : Green-AP : Detached>>> >>> Green-AP : Detached>>> ol_if_spectral_detach>>> SPECTRAL : Module removed (spectral = cc30c000)>>> ol_ath_detach: remove global_ic[1]..gloabl_ic ptr:bf6a1df8>>> ol_ath_detach: Peer Count 531 >>> ath_ahb_remove>>> ol_wifi_assoc_netlink_fini wifiassoc_nl is NULL>>> osif_wrap_devt_detach:422 osif wrap dev table detached>>> osif_wrap_detach:475 osif wrap detached>>> ath_lowi_if_netlink_delete Going to decrement current LOWI netlink ref count: 1>>> ol_if_dfs_teardown: called >>> ol_if_dfs_clist_update: called, cmd=1, nollist= (null), nentries=0>>> ol_ath_phyerr_detach: called>>> ieee80211_bsteering_detach: Band steering terminated>>> acfg_detach Netlink socket released>>> ieee80211_ifdetach: ATF terminated>>> Green-AP : Green-AP : Detached>>> >>> Green-AP : Detached>>> ol_if_spectral_detach>>> SPECTRAL : Module removed (spectral = cd29c000)>>> ol_ath_detach: remove global_ic[0]..gloabl_ic ptr:bf6a1df8>>> ol_ath_detach: Peer Count 531 >>> ath_ahb_remove>>> Removing athdebug proc file>>> ath_dev: driver unloaded>>> ath_spectral: driver unloaded>>> ath_rate_atheros: driver unloaded>>> ath_tx99: driver unloaded>>> ath_hal: driver unloaded>>> ath_dfs: driver unloaded>>> ____________________________________________________________________________Preemptible hierarchical RCU implementation.NR_IRQS:16 nr_irqs:16 16Architected cp15 timer(s) running at 48.00MHz (virt).sched_clock: 56 bits at 48MHz, resolution 20ns, wraps every 2863311552512nsSwitching to timer-based delay loopCalibrating delay loop (skipped), value calculated using timer frequency.. 96.00 BogoMIPS (lpj=480000)pid_max: default: 32768 minimum: 301Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)CPU: Testing write buffer coherency: okCPU0: thread -1, cpu 0, socket 0, mpidr 80000000Setting up static identity map for 0x802133c0 - 0x80213418CPU1: Booted secondary processorCPU1: thread -1, cpu 1, socket 0, mpidr 80000001CPU2: Booted secondary processorCPU2: thread -1, cpu 2, socket 0, mpidr 80000002CPU3: Booted secondary processorCPU3: thread -1, cpu 3, socket 0, mpidr 80000003Brought up 4 CPUsSMP: Total of 4 processors activated (384.00 BogoMIPS).CPU: All CPU(s) started in SVC mode.VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5pinctrl core: initialized pinctrl subsystemregulator-dummy: no parametersNET: Registered protocol family 16DMA: preallocated 2048 KiB pool for atomic coherent allocationscpuidle: using governor laddercpuidle: using governor menuhw-breakpoint: Debug register access (0xee003e17) caused undefined instruction on CPU 1hw-breakpoint: Debug register access (0xee003e17) caused undefined instruction on CPU 3hw-breakpoint: Debug register access (0xee003e17) caused undefined instruction on CPU 2hw-breakpoint: CPU 3 failed to disable vector catchhw-breakpoint: Debug register access (0xee003e17) caused undefined instruction on CPU 0Version Rollback Feature Disabledgpiochip_add: registered GPIOs 0 to 69 on device: 1000000.pinctrlGPIO chip 1000000.pinctrl: created GPIO range 0->69 ==> 1000000.pinctrl PIN 0->69i2c-msm-v2 78b7000.i2c: probing driver i2c-msm-v2sps:sps is ready.bio: create slab <bio-0> at 0SD0 VccQ: 1800 <--> 3000 mV SCSI subsystem initializedmsm_bus_fabric_init_drivermsm_bus_device 580000.ad-hoc-bus: Util-fact is missing, default to 100msm_bus_device 580000.ad-hoc-bus: Vrail-comp is missing, default to 100msm_bus_device 580000.ad-hoc-bus: Failed to get bus clk for bus4096 ctx1msm_bus_device 580000.ad-hoc-bus: Util-fact is missing, default to 100msm_bus_device 580000.ad-hoc-bus: Vrail-comp is missing, default to 100msm_bus_device 580000.ad-hoc-bus: Failed to get bus clk for bus1024 ctx1Bluetooth: Core ver 2.18NET: Registered protocol family 31Bluetooth: HCI device and connection manager initializedBluetooth: HCI socket layer initializedBluetooth: L2CAP socket layer initializedBluetooth: SCO socket layer initialized80000.qcom,pcie supply vreg-3.3 not found, using dummy regulator80000.qcom,pcie supply vreg-1.8 not found, using dummy regulator80000.qcom,pcie supply vreg-0.9 not found, using dummy regulator80000.qcom,pcie supply gdsc-vdd not found, using dummy regulatorof_get_named_gpiod_flags exited with status 0of_get_named_gpiod_flags exited with status 0of_get_named_gpiod_flags exited with status 0msm_pcie_enable: msm_pcie_enable: PCIe: trigger the reset of endpoint of RC0.msm_pcie_enable: msm_pcie_enable: PCIe RC0 PHY is ready!msm_pcie_enable: msm_pcie_enable: PCIe: Release the reset of endpoint of RC0.msm_pcie_enable: msm_pcie_enable: PCIe RC0 link initializedmsm_pcie 80000.qcom,pcie: PCI host bridge to bus 0000:00pci_bus 0000:00: root bus resource [io 0x40200000-0x402fffff]pci_bus 0000:00: root bus resource [mem 0x40300000-0x40ffffff]pci_bus 0000:00: No busn resource found for root bus, will use [bus 00-ff]pci 0000:00:00.0: [17cb:1001] type 01 class 0x060400msm_pcie_oper_conf: msm_pcie_oper_conf: Read of RC0 0:0x00 + 0x0014[4] is all FFspci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x00000fff 64bit]pci 0000:00:00.0: PME# supported from D0 D3hot D3coldPCI: bus0: Fast back to back transfers disabledpci 0000:00:00.0: bridge configuration invalid ([bus 00-00]), reconfiguringpci 0000:01:00.0: [168c:0056] type 00 class 0x028000msm_pcie_oper_conf: msm_pcie_oper_conf: Read of RC0 1:0x00 + 0x0014[4] is all FFspci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit]pci 0000:01:00.0: PME# supported from D0 D3hotPCI: bus1: Fast back to back transfers disabledpci_bus 0000:01: busn_res: [bus 01-ff] end is updated to 01pci_bus 0000:00: busn_res: [bus 00-ff] end is updated to 01msm_pcie_oper_conf: msm_pcie_oper_conf: Read of RC0 0:0x00 + 0x0028[4] is all FFspci 0000:00:00.0: BAR 8: assigned [mem 0x40400000-0x405fffff]pci 0000:00:00.0: BAR 0: assigned [mem 0x40300000-0x40300fff 64bit]pci 0000:01:00.0: BAR 0: assigned [mem 0x40400000-0x405fffff 64bit]pci 0000:00:00.0: PCI bridge to [bus 01]pci 0000:00:00.0: bridge window [mem 0x40400000-0x405fffff]msm_pcie_probe: msm_pcie_probe: RC0 is enabled in bootupSwitched to clocksource arch_sys_counterNET: Registered protocol family 2TCP established hash table entries: 2048 (order: 1, 8192 bytes)TCP bind hash table entries: 2048 (order: 2, 16384 bytes)TCP: Hash tables configured (established 2048 bind 2048)TCP: reno registeredUDP hash table entries: 256 (order: 1, 8192 bytes)UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)NET: Registered protocol family 1hw perfevents: enabled with ARMv7 Cortex-A7 PMU driver, 5 counters availablefutex hash table entries: 1024 (order: 4, 65536 bytes)squashfs: version 4.0 (2009/01/31) Phillip Loughermsgmni has been set to 490Key type asymmetric registeredAsymmetric key parser 'x509' registeredio scheduler noop registeredio scheduler deadline registered (default)tcsr 194b000.tcsr: setting usb hs phy mode select = e700e7tcsr 1953000.ess_tcsr: setting ess interface select = 0tcsr 1949000.tcsr: setting wifi_glb_cfg = 41000000tcsr 1957000.tcsr: setting wifi_noc_memtype_m0_m2 = 2222222Serial: 8250/16550 driver, 2 ports, IRQ sharing disabledipq40xx-pinctrl 1000000.pinctrl: could not parse property pinsmsm_serial 78af000.serial: msm_serial: detected port #0msm_serial 78af000.serial: uartclk = 184320078af000.serial: ttyMSM0 at MMIO 0x78af000 (irq = 139, base_baud = 115200) is a MSMmsm_serial: console setup on port #0console [ttyMSM0] enabledmsm_serial: driver initializedmsm_serial_hsl_init: driver initializedof_get_named_gpiod_flags: can't parse gpios property of node '/soc/uart@78b0000[0]'of_get_named_gpiod_flags: can't parse gpios property of node '/soc/uart@78b0000[0]'of_get_named_gpiod_flags: can't parse gpios property of node '/soc/uart@78b0000[0]'of_get_named_gpiod_flags: can't parse gpios property of node '/soc/uart@78b0000[0]'BLSP UART: Bus scaling is disabled.unregister_client_adhoc: Null cl handle passed unregistermsm_serial_hs: probe of 78b0000.uart failed with error -2msm_serial_hs module loadedof_get_named_gpiod_flags: can't parse gpios property of node '/soc/uart@78b0000[0]'uart_tx_gpio is not availableof_get_named_gpiod_flags: can't parse gpios property of node '/soc/uart@78b0000[0]'uart_rx_gpio is not availableof_get_named_gpiod_flags: can't parse gpios property of node '/soc/uart@78b0000[0]'uart_cts_gpio is not availableof_get_named_gpiod_flags: can't parse gpios property of node '/soc/uart@78b0000[0]'uart_rfr_gpio is not availableWakeup irq not specified.BLSP UART: Bus scaling is disabled.sps: BAM device 0x07884000 is not registered yet.sps:BAM 0x07884000 is registered.78b0000.uart: ttyQHS0 at MMIO 0x78b0000 (irq = 140, base_baud = 460800) is a MSM HS UARTqca_serial_hs module loadedbrd: module loadedsps: BAM device 0x07984000 is not registered yet.sps:BAM 0x07984000 is registered.msm_nand_bam_init: msm_nand_bam_init: BAM device registered: bam_handle 0xcf052600sps:BAM 0x07984000 (va:0xd0a60000) enabled: ver:0x19, number of pipes:7msm_nand_version_check: nand_major:1, nand_minor:4, qpic_major:1, qpic_minor:4msm_nand_flash_onfi_probe: Found an ONFI compliant device MX30LF1G18AC msm_nand_scan: NAND Id: 0x9580f1c2 Buswidth: 8Bits Density: 128 MBytemsm_nand_scan: pagesize: 2048 Erasesize: 131072 oobsize: 64 (in Bytes)msm_nand_scan: BCH ECC: 4 Bitmsm_nand_scan: CFG0: 0x2a0408c0, CFG1: 0x0804745c RAWCFG0: 0x280420c0, RAWCFG1: 0x0005045d ECCBUFCFG: 0x00000203, ECCBCHCFG: 0x42040700 BAD BLOCK BYTE: 0x000001d12 ofpart partitions found on MTD device 7980000.qcom,nandCreating 2 MTD partitions on "7980000.qcom,nand":0x000000000000-0x000000400000 : "Bootloader"0x000000400000-0x000008000000 : "UBI_DEV"msm_nand_probe: NANDc phys addr 0x7980000, BAM phys addr 0x7984000, BAM IRQ 133msm_nand_probe: Allocated DMA buffer at virt_addr 0xd0a7b000, phys_addr 0x8f058000of_get_named_gpiod_flags: can't parse gpios property of node '/soc/spi@78b5000[0]'of_get_named_gpiod_flags: can't parse gpios property of node '/soc/spi@78b5000[0]'of_get_named_gpiod_flags: can't parse gpios property of node '/soc/spi@78b5000[0]'of_get_named_gpiod_flags: can't parse gpios property of node '/soc/spi@78b5000[0]'of_get_named_gpiod_flags: can't parse gpios property of node '/soc/spi@78b5000[0]'of_get_named_gpiod_flags: can't parse gpios property of node '/soc/spi@78b5000[0]'of_get_named_gpiod_flags: can't parse gpios property of node '/soc/spi@78b5000[0]'IMQ driver loaded successfully. (numdevs = 2, numqueues = 1) Hooking IMQ after NAT on PREROUTING. Hooking IMQ before NAT on POSTROUTING.of_get_named_gpiod_flags exited with status 0phy_reset_gpio is 41libphy: ipq40xx_mdio: probedipq40xx-mdio 90000.mdio: ipq40xx-mdio driver was registeredPPP generic driver version 2.4.2PPP MPPE Compression module registeredNET: Registered protocol family 24PPTP driver version 0.8.5i2c /dev entries driverrequesting memory region failedof_get_named_gpiod_flags: can't parse gpios property of node '/soc/i2c@78b7000/lp55231@32[0]'lp5523x 0-0032: lp5523 Programmable led chip foundnf_conntrack version 0.5.0 (3925 buckets, 15700 max)xt_time: kernel timezone is -0000gre: GRE over IPv4 demultiplexor driverip_tables: (C) 2000-2006 Netfilter Core Teamarp_tables: (C) 2002 David S. MillerTCP: cubic registeredNET: Registered protocol family 10ip6_tables: (C) 2000-2006 Netfilter Core TeamNET: Registered protocol family 17Bridge firewalling registeredBluetooth: RFCOMM TTY layer initializedBluetooth: RFCOMM socket layer initializedBluetooth: RFCOMM ver 1.11Bluetooth: BNEP (Ethernet Emulation) ver 1.3Bluetooth: BNEP filters: protocol multicastBluetooth: BNEP socket layer initializedl2tp_core: L2TP core driver, V2.0l2tp_ppp: PPPoL2TP kernel driver, V2.0l2tp_netlink: L2TP netlink interface8021q: 802.1Q VLAN Support v1.8Registering SWP/SWPB emulation handlerSD0 VccQ: disablingregulator-dummy: disablingUBI: attaching mtd1 to ubi0UBI: scanning is finishedUBI: attached mtd1 (name "UBI_DEV", size 124 MiB) to ubi0UBI: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytesUBI: min./max. I/O unit sizes: 2048/2048, sub-page size 2048UBI: VID header offset: 2048 (aligned 2048), data offset: 4096UBI: good PEBs: 991, bad PEBs: 1, corrupted PEBs: 0UBI: user volume: 6, internal volumes: 1, max. volumes count: 128UBI: max/mean erase counter: 138/77, WL threshold: 4096, image sequence number: 2108563064UBI: available PEBs: 20, total reserved PEBs: 971, PEBs reserved for bad PEB handling: 19UBI: background thread "ubi_bgt0d" started, PID 74gluebi_create: Hook read/write method of Factory.gluebi_create: Hook read/write method of Factory2.[Factory-0]: OK (ver: 41)[Factory2-0]: OK (ver: 41)Select [Factory-0]volume linux rfs_offset 21b580 mtd->size 3013000Creating 1 MTD partitions on "linux":0x00000021b580-0x000003013000 : "rootfs"mtd: device 6 (rootfs) set to be root filesystemvolume linux2 rfs_offset 21b580 mtd->size 3013000Creating 1 MTD partitions on "linux2":0x00000021b580-0x000003013000 : "rootfs2"gluebi_create: skip jffs2 volumeclk: Not disabling unused clocksVFS: Mounted root (squashfs filesystem) readonly on device 31:6.Freeing unused kernel memory: 176K (c074e000 - c077a000)offset 0x0 elapse 40msfound private data block and skip itnvram_commit(): pid 1 comm [init]found private data block and skip itssdk_alloc_priv[4402]:INFO:ess-switch dts node number: 1ssdk_dt_parse[2643]:INFO:ess-switch DT exist!ssdk_dt_parse[2672]:INFO:switch_access_mode: local busssdk_dt_parse_mac_mode[2271]:INFO:mac mode = 0x0ssdk_dt_parse_mac_mode[2277]:INFO:mac mode1 doesn't exit!ssdk_dt_parse_mac_mode[2286]:INFO:mac mode2 doesn't exit!ssdk_dt_parse_uniphy[2305]:INFO:ess-uniphy DT doesn't exist!ssdk_dt_parse_scheduler_cfg[2495]:ERROR:cannot find port_scheduler_resource nodessdk_dt_parse_phy_info[2538]:INFO:qcom,port_phyinfo DT doesn't exist!ssdk_dt_parse_mdio[2575]:INFO:mdio DT exist!ssdk_dt_parse[2698]:INFO:switchreg_base_addr: 0xc000000ssdk_dt_parse[2699]:INFO:switchreg_size: 0x80000ssdk_dt_parse[2708]:INFO:ess-psgmii DT exist!ssdk_dt_parse[2765]:INFO:current dts led_source_num is 5ssdk_plat_init startenable ess clkmalibu_phy_api_ops_init[2505]:INFO:qca probe malibu phy driver succeeded!regi_init[4507]:INFO:Initializing DESS!!ssdk_switch_register[1588]:INFO:Chip version 0x1401qca_link_polling_select[1282]:INFO:link-polling-required node does not existssdk_switch_register[1611]:INFO:polling is selectedregi_init[4516]:INFO:Initializing DESS Done!!regi_init[4540]:INFO:qca-ssdk module init succeeded!QCA Hy-Fi multicast installation successfullymem_manager: module license 'unspecified' taints kernel.Disabling lock debugging due to kernel taintath_dfs: Version 2.0.0Copyright (c) 2005-2006 Atheros Communications, Inc. All Rights Reservedath_spectral: Version 2.0.0Copyright (c) 2005-2009 Atheros Communications, Inc. All Rights Reservedath_hal: 0.9.17.1 (WRITE_EEPROM, 11D)ath_rate_atheros: Copyright (c) 2001-2005 Atheros Communications, Inc, All Rights Reservedath_tx99: Version 2.0Copyright (c) 2010 Atheros Communications, Inc, All Rights Reservedath_dev: Copyright (c) 2001-2007 Atheros Communications, Inc, All Rights Reserved *********** IPQ4019 *************Wifi0 CPU frequency 250000000hif_target_sync_ahb: Got FW signal, retries = 1hif_ahb_enable_bus: X - hif_type = 0xd, target_type = 0xbhif_config_ce: ce_init donehif_config_ce: X, ret = 0hif_set_hia: Ehif_pci_bus_configure: hif_set_hia donehif_configure_irq: Ehif_enable: X OKhif_napi_create: NAPI structures initializedhif_napi_create: NAPI id 6 created for pipe 5qca_napi_create: napi instance 32 created on pipe 4hif_napi_event: received evnt: CONF cmd; v = 1 (state=0x1)hif_napi_event: setting configuration to ON__ol_ath_attach() Allocated scn cdf804c0__ol_ath_attach: dev name wifi0ol_ath_attach interface_id 0ol_target_init() BMI inited.ol_target_init() BMI Get Target Info.Chip id: 0xb, chip version: 0x1000000 CE WAR DisabledNUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0ol_target_init() configure Target . Target Version is 1000000 Flash Download Address c0000 ol_transfer_bin_file: flash data file definedol_transfer_bin_file[3815] Get Caldata for wifi0.qc98xx_verify_checksum: flash checksum passed: 0x4235ol_transfer_bin_file 3881: Download Flash data len 12064Board extended Data download address: 0x0 Board data initializedol_ath_download_firmware: Download OTP, flash download ADDRESS 0xc0000 Selecting OTP binary for CHIP Version -1065183676ath10k_ahb a000000.wifi: Direct firmware load failed with error 0ath10k_ahb a000000.wifi: Falling back to user helperath10k_ahb a000000.wifi: Firmware loaded from user helper succesfullyol_transfer_bin_file 3678: downloading file 0, Download data len 4676 First OTP send param 8000ol_ath_download_firmware :First OTP download and Execute is good address:0x5000 return param 4660ol_ath_download_firmware:##Board Id 20 , CHIP Id 0ol_ath_download_firmware: BOARDDATA DOWNLOAD TO address 0xc0000 wifi0: Selecting board data file name boardData_1_0_IPQ4019_DK04_2G.binol_transfer_bin_file: Board Data File download to address=0xc0000 file name=IPQ4019/hw.1/boardData_1_0_IPQ4019_DK04_2G.binath10k_ahb a000000.wifi: Direct firmware load failed with error 0ath10k_ahb a000000.wifi: Falling back to user helperath10k_ahb a000000.wifi: Firmware loaded from user helper succesfullyol_transfer_bin_file 3678: downloading file 3, Download data len 12064Board extended Data download address: 0x0ol_ath_download_firmware: Using 0x1234 for the remainder of init Selecting OTP binary for CHIP Version -1065183676ath10k_ahb a000000.wifi: Direct firmware load failed with error 0ath10k_ahb a000000.wifi: Falling back to user helperath10k_ahb a000000.wifi: Firmware loaded from user helper succesfullyol_transfer_bin_file 3678: downloading file 0, Download data len 4676 [Flash] : Ignore Module param Second otp download Param 10000 ol_ath_download_firmware : Second OTP download and Execute is good, param=0x0 Mission mode: Firmware CHIP Version -1065183676ath10k_ahb a000000.wifi: Direct firmware load failed with error 0ath10k_ahb a000000.wifi: Falling back to user helperath10k_ahb a000000.wifi: Firmware loaded from user helper succesfullyol_swap_seg_alloc: Successfully allocated memory for SWAP size=262144 ath10k_ahb a000000.wifi: Direct firmware load failed with error 0ath10k_ahb a000000.wifi: Falling back to user helperath10k_ahb a000000.wifi: Firmware loaded from user helper succesfullyol_swap_wlan_memory_expansion: length:185067 size_left:185087 dma_size_left:262144 fw_temp:d1b22004 fw_entry_size:185091ol_swap_wlan_memory_expansion: dma_virt_addr :d1ae1000 fw_temp: d1b22008 length: 185067Swap: bytes_left to copy: fw:16; dma_page:77077ol_swap_wlan_memory_expansion: length:0 size_left:12 dma_size_left:77077 fw_temp:d1b4f2f7 fw_entry_size:185091Swap: wrong length read:0ol_swap_wlan_memory_expansion: Swap total_bytes copied: 185067 Target address 4180b0 scn=cdf804c0 target_write_addr=4180b0 seg_info=cf219c10 ol_transfer_swap_struct:Code swap structure successfully downloaded for bin type =2 bin_filename=IPQ4019/hw.1/athwlan.bin swap_filename=/lib/firmware/IPQ4019/hw.1/athwlan.codeswap.bin ol_transfer_bin_file: Downloading firmware file: IPQ4019/hw.1/athwlan.binath10k_ahb a000000.wifi: Direct firmware load failed with error 0ath10k_ahb a000000.wifi: Falling back to user helperath10k_ahb a000000.wifi: Firmware loaded from user helper succesfullyol_transfer_bin_file 3678: downloading file 1, Download data len 378664ol_target_init() Download FW done. ERROR: No wifi_dump dts node available in the dts entry fileol_ath_attach() WMI attached. wmi_handle cf012000 wmi_unified_register_event_handler: Event id 62 is unavailable+htc_create .. HIF :ce3d0000-htc_create: (0xcf094800)htc_wmi_init() HT Create . cf094800htc_wmi_init 7762 host_enable 0 nss_nwifi_offload 0ol_ath_set_default_tgt_config : AC Minfree buffer allocation through module param (umac.ko) OL_ACBKMinfree : 0 OL_ACBEMinfree : 0 OL_ACVIMinfree : 0 OL_ACVOMinfree : 0hif_enable_fastpath, Enabling fastpath mode+HWThif_completion_thread_startup: pipe_num:0 pipe_info:0xce3d4578hif_completion_thread_startup: pipe_num:3 pipe_info:0xce3d4650hif_completion_thread_startup: pipe_num:4 pipe_info:0xce3d4698-HWTStartup Mode-0 set<=== cfg max peer id 1056 ====>htt_peer_map_timer_init Enter pdev cd4b8000 hrtimer cd4bc948 htt_alloc_peer_map_mem : Alloc Success : host q vaddr cdc0c000 paddr 8dc0c000 htt_alloc_peer_map_mem : Flush Interval Configured to 256 pktsol_txrx_pdev_attach: 2500 tx desc's allocated ; range starts from cd140000Firmware_Build_Number:50 FW wireless modes: 0x680cnum_rf_chain:0x00000002 ht_cap_info:0x0000085b vht_cap_info:0x339959b2 vht_supp_mcs:0x0000fffabtcoex_support 0, wlan_prio_gpio 0, coex_gpio_pin 0 0 0wmi_service_coex_gpio 1, wmi_service_4_wire_coex_support 1, coex_version 0Sending Ext resource cfg: HOST PLATFORM as 0fw_feature_bitmap as 50 to TGTol_ath_service_ready_event: tt_support: 1ol_ath_service_ready_event: periodic_chan_stats: 1ol_ath_service_ready_event: sw_cal_support_check_flag: 1Peer Caching Enabled ; num_peers = 530, num_active_peers = 52 num_tids = 104, num_vdevs = 17EXT NSS Supportedidx 1 req 2 num_units 1 num_unit_info 12 unit size 256 actual units 53 ol_ath_alloc_host_mem_chunk req_id 2 idx 0 num_units 53 unit_len 256,idx 2 req 3 num_units 1 num_unit_info 12 unit size 1024 actual units 53 ol_ath_alloc_host_mem_chunk req_id 3 idx 1 num_units 53 unit_len 1024,idx 3 req 4 num_units 1 num_unit_info 12 unit size 4096 actual units 53 ol_ath_alloc_host_mem_chunk req_id 4 idx 2 num_units 53 unit_len 4096,idx 0 req 1 num_units 0 num_unit_info 2 unit size 744 actual units 531 ol_ath_alloc_host_mem_chunk req_id 1 idx 3 num_units 531 unit_len 744,idx 4 req 6 num_units 35 num_unit_info 0 unit size 3072 actual units 35 ol_ath_alloc_host_mem_chunk req_id 6 idx 4 num_units 35 unit_len 3072,idx 5 req 7 num_units 1 num_unit_info 0 unit size 6144 actual units 1 ol_ath_alloc_host_mem_chunk req_id 7 idx 5 num_units 1 unit_len 6144,idx 6 req 5 num_units 0 num_unit_info 2 unit size 2052 actual units 531 ol_ath_alloc_host_mem_chunk req_id 5 idx 6 num_units 531 unit_len 2052,Support not added yet for Service 91Support not added yet for Service 92No EXT_MSG send INIT nowchunk 0 len 13568 requested , ptr 0x8dea0000chunk 1 len 54272 requested , ptr 0x8d130000chunk 2 len 217088 requested , ptr 0x8d1c0000chunk 3 len 395064 requested , ptr 0x8d200000chunk 4 len 107520 requested , ptr 0x8d1a0000chunk 5 len 6144 requested , ptr 0x8dc40000chunk 6 len 1089612 requested , ptr 0x8cc00000chunk 7 len 0 requested , ptr 0x0ol_ath_service_ready_event[4259] WAPI MBSSID 2 smart_log_init: Smart logging Enabled buf=ccd10000 (size=65536)Version = 16777216 3 status = 0ol_ath_connect_htc() WMI is readytarget uses HTT version 2.2; host uses 2.2htt_h2t_frag_desc_bank_cfg_msg - HTT_H2T_MSG_TYPE_FRAG_DESC_BANK_CFG sent to FW for radio ID = 0ol_ath_attach() connect HTC. bypasswmi : 0ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0.ol_regdmn_init_channels: !avail mode 0x680c (0x2) flags 0x2150ol_regdmn_init_channels: !avail mode 0x680c (0x1) flags 0x140ol_regdmn_init_channels: !avail mode 0x680c (0x20) flags 0xd0ol_regdmn_init_channels: !avail mode 0x680c (0x40) flags 0x150ol_regdmn_init_channels: !avail mode 0x680c (0x1000) flags 0x10100ol_regdmn_init_channels: !avail mode 0x680c (0x8000) flags 0x20100ol_regdmn_init_channels: !avail mode 0x680c (0x10000) flags 0x40100ol_regdmn_init_channels: !avail mode 0x680c (0x20000) flags 0x100100ol_regdmn_init_channels: !avail mode 0x680c (0x40000) flags 0x200100ol_regdmn_init_channels: !avail mode 0x680c (0x80000) flags 0x400100ol_regdmn_init_channels: !avail mode 0x680c (0x100000) flags 0x800100ol_regdmn_init_channels: !avail mode 0x680c (0x200000) flags 0x4000100ol_regdmn_init_channels: !avail mode 0x680c (0x400000) flags 0x8000100ol_ath_phyerr_attach: calledOL Resmgr Init-edieee80211_bsteering_attach: Band steering initializedacfg_attach: 3013: Netlink socket created:cf235000ol_if_spectral_setupSPECTRAL : get_capability not registeredHAL_CAP_PHYDIAG : CapableSPECTRAL : Need to fix the capablity check for RADAR (spectral_attach : 237)SPECTRAL : get_capability not registeredHAL_CAP_RADAR : CapableSPECTRAL : Need to fix the capablity check for SPECTRAL (spectral_attach : 242)SPECTRAL : get_capability not registeredHAL_CAP_SPECTRAL_SCAN : CapableSPECTRAL : get_tsf64 not registeredspectral_init_netlink 78 NULL SKBGreen-AP : Green-AP : AttachedGreen-AP : Attachedrate power table override is only supported for AR98XXol_ath_smart_ant_attach: Hardware doest not support Smart Antenna.ol_if_dfs_setup: called ol_if_dfs_attach: called; ptr=cd26998c, radar_info=ce31dbd8dfs_attach: event log enabled by defaultol_ath_rtt_meas_report_attach: calledol_ath_lowi_wmi_event_attach: called>>>> CB Set (null)ol_ath_attach() UMAC attach . BURSTING enabled by defaultol_ath_attach: Set global_ic[1] ..ptr:bf6a1df8ath_lowi_if_netlink_init LOWI Netlink successfully createdosif_wrap_attach:444 osif wrap attachedosif_wrap_devt_init:405 osif wrap dev table init done Wrap Attached: Wrap_com =cf233a00 ic->ic_wrap_com=cf233a00 &wrap_com->wc_devt=cf233a00 __ol_ath_attach: needed_headroom reservation 60ol_ath_thermal_mitigation_attach: --ol_ath_ahb_probe num_radios=0, wifi_radios[0].sc = cdf804c0 wifi_radio_type = 2ath_sysfs_diag_init: diag_fsattr *********** IPQ4019 *************Wifi1 CPU frequency 250000000hif_target_sync_ahb: Got FW signal, retries = 1hif_ahb_enable_bus: X - hif_type = 0xd, target_type = 0xbhif_config_ce: ce_init donehif_config_ce: X, ret = 0hif_set_hia: Ehif_pci_bus_configure: hif_set_hia donehif_configure_irq: Ehif_enable: X OKhif_napi_create: NAPI structures initializedhif_napi_create: NAPI id 6 created for pipe 5qca_napi_create: napi instance 32 created on pipe 4hif_napi_event: received evnt: CONF cmd; v = 1 (state=0x1)hif_napi_event: setting configuration to ON__ol_ath_attach() Allocated scn cd2804c0__ol_ath_attach: dev name wifi1ol_ath_attach interface_id 1ol_target_init() BMI inited.ol_target_init() BMI Get Target Info.Chip id: 0xb, chip version: 0x1000000 CE WAR DisabledNUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0ol_target_init() configure Target . Target Version is 1000000 Flash Download Address c0000 ol_transfer_bin_file: flash data file definedol_transfer_bin_file[3815] Get Caldata for wifi1.qc98xx_verify_checksum: flash checksum passed: 0xaea5ol_transfer_bin_file 3881: Download Flash data len 12064Board extended Data download address: 0x0 Board data initializedol_ath_download_firmware: Download OTP, flash download ADDRESS 0xc0000 Selecting OTP binary for CHIP Version -1065183676ath10k_ahb a800000.wifi: Direct firmware load failed with error 0ath10k_ahb a800000.wifi: Falling back to user helperath10k_ahb a800000.wifi: Firmware loaded from user helper succesfullyol_transfer_bin_file 3678: downloading file 0, Download data len 4676 First OTP send param 8000ol_ath_download_firmware :First OTP download and Execute is good address:0x5400 return param 4660ol_ath_download_firmware:##Board Id 21 , CHIP Id 0ol_ath_download_firmware: BOARDDATA DOWNLOAD TO address 0xc0000 wifi1: Selecting board data file name boardData_1_0_IPQ4019_DK04_5G.binol_transfer_bin_file: Board Data File download to address=0xc0000 file name=IPQ4019/hw.1/boardData_1_0_IPQ4019_DK04_5G.binath10k_ahb a800000.wifi: Direct firmware load failed with error 0ath10k_ahb a800000.wifi: Falling back to user helperath10k_ahb a800000.wifi: Firmware loaded from user helper succesfullyol_transfer_bin_file 3678: downloading file 3, Download data len 12064Board extended Data download address: 0x0ol_ath_download_firmware: Using 0x1234 for the remainder of init Selecting OTP binary for CHIP Version -1065183676ath10k_ahb a800000.wifi: Direct firmware load failed with error 0ath10k_ahb a800000.wifi: Falling back to user helperath10k_ahb a800000.wifi: Firmware loaded from user helper succesfullyol_transfer_bin_file 3678: downloading file 0, Download data len 4676 [Flash] : Ignore Module param Second otp download Param 10000 ol_ath_download_firmware : Second OTP download and Execute is good, param=0x0 Mission mode: Firmware CHIP Version -1065183676ath10k_ahb a800000.wifi: Direct firmware load failed with error 0ath10k_ahb a800000.wifi: Falling back to user helperath10k_ahb a800000.wifi: Firmware loaded from user helper succesfullyol_swap_seg_alloc: Successfully allocated memory for SWAP size=262144 ath10k_ahb a800000.wifi: Direct firmware load failed with error 0ath10k_ahb a800000.wifi: Falling back to user helperath10k_ahb a800000.wifi: Firmware loaded from user helper succesfullyol_swap_wlan_memory_expansion: length:185067 size_left:185087 dma_size_left:262144 fw_temp:d1f1a004 fw_entry_size:185091ol_swap_wlan_memory_expansion: dma_virt_addr :d1ed9000 fw_temp: d1f1a008 length: 185067Swap: bytes_left to copy: fw:16; dma_page:77077ol_swap_wlan_memory_expansion: length:0 size_left:12 dma_size_left:77077 fw_temp:d1f472f7 fw_entry_size:185091Swap: wrong length read:0ol_swap_wlan_memory_expansion: Swap total_bytes copied: 185067 Target address 4180b0 scn=cd2804c0 target_write_addr=4180b0 seg_info=ccdf5510 ol_transfer_swap_struct:Code swap structure successfully downloaded for bin type =2 bin_filename=IPQ4019/hw.1/athwlan.bin swap_filename=/lib/firmware/IPQ4019/hw.1/athwlan.codeswap.bin ol_transfer_bin_file: Downloading firmware file: IPQ4019/hw.1/athwlan.bin[wifi0] FWLOG: [42957] WAL_DBGID_RST_STATS ( 0x1ath10k_ahb a800000.wifi: Direct firmware load failed with error 0ath10k_ahb a800000.wifi: Falling back to user helper, 0x1, 0x96c, 0x0 )[wifi0] FWLOG: [42984] WAL_DBGID_TX_AC_BUFFER_SET ( 0x3, 0x1e, 0x94c, 0x94c, 0x0 )[wifi0] FWLOG: [42984] WAL_DBGID_TX_AC_BUFFER_SET ( 0x12ath10k_ahb a800000.wifi: Firmware loaded from user helper succesfullyol_transfer_bin_file 3678: downloading file 1, Download data len 378664, 0x1e, 0x94c, 0x94c, 0x0 )[wifi0] FWLOG: [42984] WAL_DBGID_TX_AC_BUFFER_SET ( 0x45, 0x1e, 0x94c, 0x94c, 0x0 )[wifi0] FWLOG: [42984] WAL_DBGID_TX_AC_BUFFER_SET ( 0x67, 0x1e, 0x94c, 0x94c, 0x0 )[wifi0] FWLOG: [43093] WAL_DBGID_PDEV_INFO_PRINT ( 0x3a, 0xa10, 0x160, 0x0, 0x12 )[wifi0] FWLOG: [43093] WAL_DBGID_PDEV_INFO_PRINT ( 0x3a, 0x0, 0x12, 0x10, 0x12 )random: nonblocking pool is initializedol_target_init() Download FW done. ERROR: No wifi_dump dts node available in the dts entry fileol_ath_attach() WMI attached. wmi_handle cd350000 wmi_unified_register_event_handler: Event id 62 is unavailable+htc_create .. HIF :cd2c0000-htc_create: (0xcf097000)htc_wmi_init() HT Create . cf097000htc_wmi_init 7762 host_enable 0 nss_nwifi_offload 0ol_ath_set_default_tgt_config : AC Minfree buffer allocation through module param (umac.ko) OL_ACBKMinfree : 0 OL_ACBEMinfree : 0 OL_ACVIMinfree : 0 OL_ACVOMinfree : 0hif_enable_fastpath, Enabling fastpath mode+HWThif_completion_thread_startup: pipe_num:0 pipe_info:0xcd2c4578hif_completion_thread_startup: pipe_num:3 pipe_info:0xcd2c4650hif_completion_thread_startup: pipe_num:4 pipe_info:0xcd2c4698-HWTStartup Mode-0 set<=== cfg max peer id 1056 ====>htt_peer_map_timer_init Enter pdev ccab8000 hrtimer ccabc948 htt_alloc_peer_map_mem : Alloc Success : host q vaddr ccac2000 paddr 8cac2000 htt_alloc_peer_map_mem : Flush Interval Configured to 256 pktsol_txrx_pdev_attach: 2500 tx desc's allocated ; range starts from cc740000Firmware_Build_Number:50 FW wireless modes: 0x1f9001num_rf_chain:0x00000002 ht_cap_info:0x0000085b vht_cap_info:0x339959b2 vht_supp_mcs:0x0000fffawmi_service_coex_gpio 0, wmi_service_4_wire_coex_support 0, coex_version 0Sending Ext resource cfg: HOST PLATFORM as 0fw_feature_bitmap as 50 to TGTol_ath_service_ready_event: tt_support: 1ol_ath_service_ready_event: periodic_chan_stats: 1ol_ath_service_ready_event: sw_cal_support_check_flag: 1Peer Caching Enabled ; num_peers = 530, num_active_peers = 52 num_tids = 104, num_vdevs = 17EXT NSS Supportedidx 1 req 2 num_units 1 num_unit_info 12 unit size 256 actual units 53 ol_ath_alloc_host_mem_chunk req_id 2 idx 0 num_units 53 unit_len 256,idx 2 req 3 num_units 1 num_unit_info 12 unit size 1024 actual units 53 ol_ath_alloc_host_mem_chunk req_id 3 idx 1 num_units 53 unit_len 1024,idx 3 req 4 num_units 1 num_unit_info 12 unit size 4096 actual units 53 ol_ath_alloc_host_mem_chunk req_id 4 idx 2 num_units 53 unit_len 4096,idx 0 req 1 num_units 0 num_unit_info 2 unit size 744 actual units 531 ol_ath_alloc_host_mem_chunk req_id 1 idx 3 num_units 531 unit_len 744,idx 4 req 6 num_units 35 num_unit_info 0 unit size 3072 actual units 35 ol_ath_alloc_host_mem_chunk req_id 6 idx 4 num_units 35 unit_len 3072,idx 5 req 7 num_units 1 num_unit_info 0 unit size 6144 actual units 1 ol_ath_alloc_host_mem_chunk req_id 7 idx 5 num_units 1 unit_len 6144,idx 6 req 5 num_units 0 num_unit_info 2 unit size 2052 actual units 531 ol_ath_alloc_host_mem_chunk req_id 5 idx 6 num_units 531 unit_len 2052,Support not added yet for Service 91Support not added yet for Service 92No EXT_MSG send INIT nowchunk 0 len 13568 requested , ptr 0x8dc04000chunk 1 len 54272 requested , ptr 0x8c730000chunk 2 len 217088 requested , ptr 0x8c7c0000chunk 3 len 395064 requested , ptr 0x8c000000chunk 4 len 107520 requested , ptr 0x8c7a0000chunk 5 len 6144 requested , ptr 0x8dc10000chunk 6 len 1089612 requested , ptr 0x8c200000chunk 7 len 0 requested , ptr 0x0ol_ath_service_ready_event[4259] WAPI MBSSID 2 smart_log_init: Smart logging Enabled buf=cc310000 (size=65536)Version = 16777216 3 status = 0ol_ath_connect_htc() WMI is readyhtt_h2t_frag_desc_bank_cfg_msg - HTT_H2T_MSG_TYPE_FRAG_DESC_BANK_CFG sent to FW for radio ID = 1target uses HTT version 2.2; host uses 2.2ol_ath_attach() connect HTC. bypasswmi : 0ol_ath_attach: low_5ghz: 5490 high_5gh: 5850 ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0.ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2) flags 0x2150ol_regdmn_init_channels: c 5180 out of range [5490..5850]ol_regdmn_init_channels: c 5200 out of range [5490..5850]ol_regdmn_init_channels: c 5220 out of range [5490..5850]ol_regdmn_init_channels: c 5240 out of range [5490..5850]ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4) flags 0xa0ol_regdmn_init_channels: !avail mode 0x1f9001 (0x8) flags 0xc0ol_regdmn_init_channels: !avail mode 0x1f9001 (0x20) flags 0xd0ol_regdmn_init_channels: !avail mode 0x1f9001 (0x40) flags 0x150ol_regdmn_init_channels: !avail mode 0x1f9001 (0x800) flags 0x10080ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2000) flags 0x20080ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4000) flags 0x40080ol_regdmn_init_channels: c 5180 out of range [5490..5850]ol_regdmn_init_channels: c 5200 out of range [5490..5850]ol_regdmn_init_channels: c 5220 out of range [5490..5850]ol_regdmn_init_channels: c 5240 out of range [5490..5850]ol_regdmn_init_channels: c 5180 out of range [5490..5850]ol_regdmn_init_channels: c 5220 out of range [5490..5850]ol_regdmn_init_channels: c 5200 out of range [5490..5850]ol_regdmn_init_channels: c 5240 out of range [5490..5850]ol_regdmn_init_channels: c 5180 out of range [5490..5850]ol_regdmn_init_channels: c 5200 out of range [5490..5850]ol_regdmn_init_channels: c 5220 out of range [5490..5850]ol_regdmn_init_channels: c 5240 out of range [5490..5850]ol_regdmn_init_channels: c 5180 out of range [5490..5850]ol_regdmn_init_channels: c 5220 out of range [5490..5850]ol_regdmn_init_channels: c 5200 out of range [5490..5850]ol_regdmn_init_channels: c 5240 out of range [5490..5850]Add VHT80 channel: 5210Add VHT80 channel: 5775ol_regdmn_init_channels: c 5180 out of range [5490..5850]ol_regdmn_init_channels: c 5200 out of range [5490..5850]ol_regdmn_init_channels: c 5220 out of range [5490..5850]ol_regdmn_init_channels: c 5240 out of range [5490..5850]Skipping VHT80 channel 5825ol_regdmn_init_channels: !avail mode 0x1f9001 (0x200000) flags 0x4000100ol_regdmn_init_channels: !avail mode 0x1f9001 (0x400000) flags 0x8000100ol_ath_phyerr_attach: calledOL Resmgr Init-edieee80211_bsteering_attach: Band steering initializedacfg_attach: Offload using existing sock cf235000ol_if_spectral_setupSPECTRAL : get_capability not registeredHAL_CAP_PHYDIAG : CapableSPECTRAL : Need to fix the capablity check for RADAR (spectral_attach : 237)SPECTRAL : get_capability not registeredHAL_CAP_RADAR : CapableSPECTRAL : Need to fix the capablity check for SPECTRAL (spectral_attach : 242)SPECTRAL : get_capability not registeredHAL_CAP_SPECTRAL_SCAN : CapableSPECTRAL : get_tsf64 not registeredspectral_init_netlink 78 NULL SKBGreen-AP : Green-AP : AttachedGreen-AP : Attachedrate power table override is only supported for AR98XXol_ath_smart_ant_attach: Hardware doest not support Smart Antenna.ol_if_dfs_setup: called ol_if_dfs_attach: called; ptr=cc06998c, radar_info=ce31dbd8dfs_attach: event log enabled by defaultol_ath_rtt_meas_report_attach: calledol_ath_lowi_wmi_event_attach: called>>>> CB Set (null)ol_ath_attach() UMAC attach . BURSTING enabled by defaultol_ath_attach: Set global_ic[2] ..ptr:bf6a1df8ath_lowi_if_netlink_init Incremented LOWI netlink ref count: 2osif_wrap_attach:444 osif wrap attachedosif_wrap_devt_init:405 osif wrap dev table init done Wrap Attached: Wrap_com =ce94f400 ic->ic_wrap_com=ce94f400 &wrap_com->wc_devt=ce94f400 __ol_ath_attach: needed_headroom reservation 60ol_ath_thermal_mitigation_attach: --ol_ath_ahb_probe num_radios=1, wifi_radios[1].sc = cd2804c0 wifi_radio_type = 2ath_sysfs_diag_init: diag_fsattr ath_ol_pci: (Atheros/multi-bss)hif_pci_enable_bus: con_mode = 0x0, device_id = 0x56PCI: enabling device 0000:00:00.0 (0144 -> 0147)PCI: enabling device 0000:01:00.0 (0140 -> 0142)hif_pci_enable_bus: hif_enable_pci done *********** QCA9888 *************hif_pci_enable_bus: hif_type = 0xe, target_type = 0xchif_pci_enable_bus: hif_pci_probe_tgt_wakeup donehif_target_sync: Loop checking FW signalhif_target_sync: Got FW signal, retries = 0hif_config_ce: ce_init donehif_config_ce: X, ret = 0hif_set_hia: Ehif_set_hia_extnd: Echip_id 0xc chip_revision 0x0 CLOCK PLL skippedhif_set_hia_extnd: setting the target pll frac ffffffff intval ffffffffhif_set_hia_extnd: no frac provided, skipping pre-configuring PLLhif_pci_bus_configure: hif_set_hia donehif_configure_irq: Ehif_pci_configure_legacy_irq: Ehif_pci_configure_legacy_irq: X, ret = 0hif_enable: X OKhif_napi_create: NAPI structures initializedhif_napi_create: NAPI id 6 created for pipe 5qca_napi_create: napi instance 32 created on pipe 4hif_napi_event: received evnt: CONF cmd; v = 1 (state=0x1)hif_napi_event: setting configuration to ON__ol_ath_attach() Allocated scn cc0c04c0__ol_ath_attach: dev name wifi2ol_ath_attach interface_id 2ol_target_init() BMI inited.ol_target_init() BMI Get Target Info.Chip id: 0xc, chip version: 0x1000000 CE WAR DisabledNUM_DEV=1 FWMODE=0x2 FWSUBMODE=0x0 FWBR_BUF 0ol_target_init() configure Target . Target Version is 1000000 Flash Download Address c0000 ol_transfer_bin_file: flash data file definedol_transfer_bin_file[3815] Get Caldata for wifi2.qc98xx_verify_checksum: flash checksum passed: 0xe839ol_transfer_bin_file 3881: Download Flash data len 12064Board extended Data download address: 0x0 Board data initializedol_ath_download_firmware: Download OTP, flash download ADDRESS 0xc0000 Selecting OTP binary for CHIP Version 0ath_ol_pci 0000:01:00.0: Direct firmware load failed with error 0ath_ol_pci 0000:01:00.0: Falling back to user helperath_ol_pci 0000:01:00.0: Firmware loaded from user helper succesfullyol_transfer_bin_file 3678: downloading file 0, Download data len 9116 First OTP send param 8000Switching to Tx Mode-1 Threshold 280[wifi1] FWLOG: [45349] WAL_DBGID_RST_STATS ( 0x1, 0x1, 0x1464, 0x0 )[wifi1] FWLOG: [45390] WAL_DBGID_TX_AC_BUFFER_SET ( 0x3, 0x1e, 0x94c, 0x94c, 0x0 )[wifi1] FWLOG: [45390] WAL_DBGID_TX_AC_BUFFER_SET ( 0x12, 0x1e, 0x94c, 0x94c, 0x0 )[wifi1] FWLOG: [45390] WAL_DBGID_TX_AC_BUFFER_SET ( 0x45ol_ath_download_firmware :First OTP download and Execute is good address:0x4400 return param 4660ol_ath_download_firmware:##Board Id 17 , CHIP Id 0, 0x1e, 0x94c, 0x94c, 0x0 )[wifi1] FWLOG: [45390] WAL_DBGID_TX_AC_BUFFER_SET ( 0x67, ol_ath_download_firmware: BOARDDATA DOWNLOAD TO address 0xc0000 wifi2: Selecting board data file name boardData_2_0_QCA9888_5G_Y9484.binol_transfer_bin_file: Board Data File download to address=0xc0000 file name=QCA9888/hw.2/boardData_2_0_QCA9888_5G_Y9484.binath_ol_pci 0000:01:00.0: Direct firmware load failed with error 0ath_ol_pci 0000:01:00.0: Falling back to user helperath_ol_pci 0000:01:00.0: Firmware loaded from user helper succesfullyol_transfer_bin_file 3678: downloading file 3, Download data len 120640x1e<6>Board extended Data download address: 0x0, 0x94c, 0x94c, 0x0 )[wifi1] FWLOG: [45492] WAL_DBGID_PDEV_INFO_PRINT ( 0x3a, 0xa10, 0x160, 0x10, 0x0 )[wifi1] FWLOG: [45492] WAL_DBGID_PDEV_INFO_PRINT ( 0x3a, 0x10, 0x0, 0x10, 0x12 )ol_ath_download_firmware: Using 0x1234 for the remainder of init Selecting OTP binary for CHIP Version 0ath_ol_pci 0000:01:00.0: Direct firmware load failed with error 0ath_ol_pci 0000:01:00.0: Falling back to user helperath_ol_pci 0000:01:00.0: Firmware loaded from user helper succesfullyol_transfer_bin_file 3678: downloading file 0, Download data len 9116 [Flash] : Ignore Module param Second otp download Param 10000 ol_ath_download_firmware : Second OTP download and Execute is good, param=0x0 Mission mode: Firmware CHIP Version 0ath_ol_pci 0000:01:00.0: Direct firmware load failed with error 0ath_ol_pci 0000:01:00.0: Falling back to user helperath_ol_pci 0000:01:00.0: Firmware loaded from user helper succesfullyol_swap_seg_alloc: Successfully allocated memory for SWAP size=262144 ath_ol_pci 0000:01:00.0: Direct firmware load failed with error 0ath_ol_pci 0000:01:00.0: Falling back to user helperath_ol_pci 0000:01:00.0: Firmware loaded from user helper succesfullyol_swap_wlan_memory_expansion: length:261907 size_left:261927 dma_size_left:262144 fw_temp:d3201004 fw_entry_size:261931ol_swap_wlan_memory_expansion: dma_virt_addr :d2fb6000 fw_temp: d3201008 length: 261907Swap: bytes_left to copy: fw:16; dma_page:237ol_swap_wlan_memory_expansion: length:0 size_left:12 dma_size_left:237 fw_temp:d3240f1f fw_entry_size:261931Swap: wrong length read:0ol_swap_wlan_memory_expansion: Swap total_bytes copied: 261907 Target address 41b0c8 scn=cc0c04c0 target_write_addr=41b0c8 seg_info=cc3fa510 ol_transfer_swap_struct:Code swap structure successfully downloaded for bin type =2 bin_filename=QCA9888/hw.2/athwlan.bin swap_filename=/lib/firmware/QCA9888/hw.2/athwlan.codeswap.bin ol_transfer_bin_file: Downloading firmware file: QCA9888/hw.2/athwlan.binath_ol_pci 0000:01:00.0: Direct firmware load failed with error 0ath_ol_pci 0000:01:00.0: Falling back to user helperath_ol_pci 0000:01:00.0: Firmware loaded from user helper succesfullyol_transfer_bin_file 3678: downloading file 1, Download data len 388448Switching to Tx Mode-1 Threshold 280ol_target_init() Download FW done. ERROR: No wifi_dump dts node available in the dts entry fileol_ath_attach() WMI attached. wmi_handle ccac6000 wmi_unified_register_event_handler: Event id 62 is unavailable+htc_create .. HIF :cc098000-htc_create: (0xcc091800)htc_wmi_init() HT Create . cc091800htc_wmi_init 7762 host_enable 0 nss_nwifi_offload 0ol_ath_set_default_tgt_config : AC Minfree buffer allocation through module param (umac.ko) OL_ACBKMinfree : 0 OL_ACBEMinfree : 0 OL_ACVIMinfree : 0 OL_ACVOMinfree : 0hif_enable_fastpath, Enabling fastpath mode+HWThif_completion_thread_startup: pipe_num:0 pipe_info:0xcc09c578hif_completion_thread_startup: pipe_num:3 pipe_info:0xcc09c650hif_completion_thread_startup: pipe_num:4 pipe_info:0xcc09c698-HWTStartup Mode-0 set<=== cfg max peer id 1056 ====>htt_peer_map_timer_init Enter pdev cb880000 hrtimer cb884948 htt_alloc_peer_map_mem : Alloc Success : host q vaddr cb910000 paddr 8b910000 htt_alloc_peer_map_mem : Flush Interval Configured to 256 pktsol_txrx_pdev_attach: 2500 tx desc's allocated ; range starts from cb500000Firmware_Build_Number:50 FW wireless modes: 0x1f9001num_rf_chain:0x00000002 ht_cap_info:0x0000085b vht_cap_info:0x339979b2 vht_supp_mcs:0x0000fffawmi_service_coex_gpio 0, wmi_service_4_wire_coex_support 0, coex_version 0Sending Ext resource cfg: HOST PLATFORM as 0fw_feature_bitmap as 50 to TGTol_ath_service_ready_event: tt_support: 1ol_ath_service_ready_event: periodic_chan_stats: 1ol_ath_service_ready_event: sw_cal_support_check_flag: 1Peer Caching Enabled ; num_peers = 530, num_active_peers = 52 num_tids = 104, num_vdevs = 17EXT NSS Supportedidx 1 req 2 num_units 1 num_unit_info 12 unit size 256 actual units 53 ol_ath_alloc_host_mem_chunk req_id 2 idx 0 num_units 53 unit_len 256,idx 2 req 3 num_units 1 num_unit_info 12 unit size 1024 actual units 53 ol_ath_alloc_host_mem_chunk req_id 3 idx 1 num_units 53 unit_len 1024,idx 3 req 4 num_units 1 num_unit_info 12 unit size 4096 actual units 53 ol_ath_alloc_host_mem_chunk req_id 4 idx 2 num_units 53 unit_len 4096,idx 0 req 1 num_units 0 num_unit_info 2 unit size 896 actual units 531 ol_ath_alloc_host_mem_chunk req_id 1 idx 3 num_units 531 unit_len 896,idx 4 req 5 num_units 0 num_unit_info 2 unit size 2068 actual units 531 ol_ath_alloc_host_mem_chunk req_id 5 idx 4 num_units 531 unit_len 2068,Support not added yet for Service 91Support not added yet for Service 92No EXT_MSG send INIT nowchunk 0 len 13568 requested , ptr 0x8d3f8000chunk 1 len 54272 requested , ptr 0x8b560000chunk 2 len 217088 requested , ptr 0x8b580000chunk 3 len 475776 requested , ptr 0x8b600000chunk 4 len 1098108 requested , ptr 0x8b000000chunk 5 len 0 requested , ptr 0x0ol_ath_service_ready_event[4259] WAPI MBSSID 2 smart_log_init: Smart logging Enabled buf=cb110000 (size=65536)Version = 16777216 3 status = 0ol_ath_connect_htc() WMI is readyhtt_h2t_frag_desc_bank_cfg_msg - HTT_H2T_MSG_TYPE_FRAG_DESC_BANK_CFG sent to FW for radio ID = 2target uses HTT version 2.2; host uses 2.2ol_ath_attach() connect HTC. bypasswmi : 0ol_ath_attach: low_5ghz: 5150 high_5gh: 5330 ol_regdmn_start: reg-domain param: regdmn=0, countryName=, wModeSelect=FFFFFFFF, netBand=FFFFFFFF, extendedChanMode=0.ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2) flags 0x2150ol_regdmn_init_channels: c 5745 out of range [5150..5330]ol_regdmn_init_channels: c 5765 out of range [5150..5330]ol_regdmn_init_channels: c 5785 out of range [5150..5330]ol_regdmn_init_channels: c 5805 out of range [5150..5330]ol_regdmn_init_channels: c 5825 out of range [5150..5330]ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4) flags 0xa0ol_regdmn_init_channels: !avail mode 0x1f9001 (0x8) flags 0xc0ol_regdmn_init_channels: !avail mode 0x1f9001 (0x20) flags 0xd0ol_regdmn_init_channels: !avail mode 0x1f9001 (0x40) flags 0x150ol_regdmn_init_channels: !avail mode 0x1f9001 (0x800) flags 0x10080ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2000) flags 0x20080ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4000) flags 0x40080ol_regdmn_init_channels: c 5745 out of range [5150..5330]ol_regdmn_init_channels: c 5765 out of range [5150..5330]ol_regdmn_init_channels: c 5785 out of range [5150..5330]ol_regdmn_init_channels: c 5805 out of range [5150..5330]ol_regdmn_init_channels: c 5825 out of range [5150..5330]ol_regdmn_init_channels: c 5745 out of range [5150..5330]ol_regdmn_init_channels: c 5785 out of range [5150..5330]ol_regdmn_init_channels: c 5765 out of range [5150..5330]ol_regdmn_init_channels: c 5805 out of range [5150..5330]ol_regdmn_init_channels: c 5745 out of range [5150..5330]ol_regdmn_init_channels: c 5765 out of range [5150..5330]ol_regdmn_init_channels: c 5785 out of range [5150..5330]ol_regdmn_init_channels: c 5805 out of range [5150..5330]ol_regdmn_init_channels: c 5825 out of range [5150..5330]ol_regdmn_init_channels: c 5745 out of range [5150..5330]ol_regdmn_init_channels: c 5785 out of range [5150..5330]ol_regdmn_init_channels: c 5765 out of range [5150..5330]ol_regdmn_init_channels: c 5805 out of range [5150..5330]Add VHT80 channel: 5210Add VHT80 channel: 5775ol_regdmn_init_channels: c 5745 out of range [5150..5330]ol_regdmn_init_channels: c 5765 out of range [5150..5330]ol_regdmn_init_channels: c 5785 out of range [5150..5330]ol_regdmn_init_channels: c 5805 out of range [5150..5330]ol_regdmn_init_channels: c 5825 out of range [5150..5330]ol_regdmn_init_channels: !avail mode 0x1f9001 (0x200000) flags 0x4000100ol_regdmn_init_channels: !avail mode 0x1f9001 (0x400000) flags 0x8000100ol_ath_phyerr_attach: calledOL Resmgr Init-edieee80211_bsteering_attach: Band steering initializedacfg_attach: Offload using existing sock cf235000ol_if_spectral_setupSPECTRAL : get_capability not registeredHAL_CAP_PHYDIAG : CapableSPECTRAL : Need to fix the capablity check for RADAR (spectral_attach : 237)SPECTRAL : get_capability not registeredHAL_CAP_RADAR : CapableSPECTRAL : Need to fix the capablity check for SPECTRAL (spectral_attach : 242)SPECTRAL : get_capability not registeredHAL_CAP_SPECTRAL_SCAN : CapableSPECTRAL : get_tsf64 not registeredspectral_init_netlink 78 NULL SKBGreen-AP : Green-AP : AttachedGreen-AP : Attachedrate power table override is only supported for AR98XXol_ath_smart_ant_attach: Hardware doest not support Smart Antenna.ol_if_dfs_setup: called ol_if_dfs_attach: called; ptr=cb1a198c, radar_info=ce31dbb0dfs_attach: event log enabled by defaultol_ath_rtt_meas_report_attach: calledol_ath_lowi_wmi_event_attach: called>>>> CB Set (null)ol_ath_attach() UMAC attach . BURSTING enabled by defaultol_ath_attach: Set global_ic[3] ..ptr:bf6a1df8ath_lowi_if_netlink_init Incremented LOWI netlink ref count: 3osif_wrap_attach:444 osif wrap attachedosif_wrap_devt_init:405 osif wrap dev table init done Wrap Attached: Wrap_com =cc7bc800 ic->ic_wrap_com=cc7bc800 &wrap_com->wc_devt=cc7bc800 __ol_ath_attach: needed_headroom reservation 60ol_ath_thermal_mitigation_attach: --ol_ath_pci_probe num_radios=2, wifi_radios[2].sc = cc0c04c0 wifi_radio_type = 2ath_sysfs_diag_init: diag_fsattr isCountryCodeValid: EEPROM regdomain 0x0ol_regdmn_init_channels: !avail mode 0x680c (0x2) flags 0x2150ol_regdmn_init_channels: !avail mode 0x680c (0x1) flags 0x140ol_regdmn_init_channels: !avail mode 0x680c (0x20) flags 0xd0ol_regdmn_init_channels: !avail mode 0x680c (0x40) flags 0x150ol_regdmn_init_channels: !avail mode 0x680c (0x1000) flags 0x10100ol_regdmn_init_channels: !avail mode 0x680c (0x8000) flags 0x20100ol_regdmn_init_channels: !avail mode 0x680c (0x10000) flags 0x40100ol_regdmn_init_channels: !avail mode 0x680c (0x20000) flags 0x100100ol_regdmn_init_channels: !avail mode 0x680c (0x40000) flags 0x200100ol_regdmn_init_channels: !avail mode 0x680c (0x80000) flags 0x400100ol_regdmn_init_channels: !avail mode 0x680c (0x100000) flags 0x800100ol_regdmn_init_channels: !avail mode 0x680c (0x200000) flags 0x4000100ol_regdmn_init_channels: !avail mode 0x680c (0x400000) flags 0x8000100isCountryCodeValid: EEPROM regdomain 0x0ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2) flags 0x2150ol_regdmn_init_channels: c 5180 out of range [5490..5850]ol_regdmn_init_channels: c 5200 out of range [5490..5850]ol_regdmn_init_channels: c 5220 out of range [5490..5850]ol_regdmn_init_channels: c 5240 out of range [5490..5850]ol_regdmn_init_channels: c 5260 out of range [5490..5850]ol_regdmn_init_channels: c 5280 out of range [5490..5850]ol_regdmn_init_channels: c 5300 out of range [5490..5850]ol_regdmn_init_channels: c 5320 out of range [5490..5850]ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4) flags 0xa0ol_regdmn_init_channels: !avail mode 0x1f9001 (0x8) flags 0xc0ol_regdmn_init_channels: !avail mode 0x1f9001 (0x20) flags 0xd0ol_regdmn_init_channels: !avail mode 0x1f9001 (0x40) flags 0x150ol_regdmn_init_channels: !avail mode 0x1f9001 (0x800) flags 0x10080ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2000) flags 0x20080ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4000) flags 0x40080ol_regdmn_init_channels: c 5180 out of range [5490..5850]ol_regdmn_init_channels: c 5200 out of range [5490..5850]ol_regdmn_init_channels: c 5220 out of range [5490..5850]ol_regdmn_init_channels: c 5240 out of range [5490..5850]ol_regdmn_init_channels: c 5260 out of range [5490..5850]ol_regdmn_init_channels: c 5280 out of range [5490..5850]ol_regdmn_init_channels: c 5300 out of range [5490..5850]ol_regdmn_init_channels: c 5320 out of range [5490..5850]ol_regdmn_init_channels: c 5180 out of range [5490..5850]ol_regdmn_init_channels: c 5220 out of range [5490..5850]ol_regdmn_init_channels: c 5260 out of range [5490..5850]ol_regdmn_init_channels: c 5300 out of range [5490..5850]ol_regdmn_init_channels: c 5200 out of range [5490..5850]ol_regdmn_init_channels: c 5240 out of range [5490..5850]ol_regdmn_init_channels: c 5280 out of range [5490..5850]ol_regdmn_init_channels: c 5320 out of range [5490..5850]ol_regdmn_init_channels: c 5180 out of range [5490..5850]ol_regdmn_init_channels: c 5200 out of range [5490..5850]ol_regdmn_init_channels: c 5220 out of range [5490..5850]ol_regdmn_init_channels: c 5240 out of range [5490..5850]ol_regdmn_init_channels: c 5260 out of range [5490..5850]ol_regdmn_init_channels: c 5280 out of range [5490..5850]ol_regdmn_init_channels: c 5300 out of range [5490..5850]ol_regdmn_init_channels: c 5320 out of range [5490..5850]ol_regdmn_init_channels: c 5180 out of range [5490..5850]ol_regdmn_init_channels: c 5220 out of range [5490..5850]ol_regdmn_init_channels: c 5260 out of range [5490..5850]ol_regdmn_init_channels: c 5300 out of range [5490..5850]ol_regdmn_init_channels: c 5200 out of range [5490..5850]ol_regdmn_init_channels: c 5240 out of range [5490..5850]ol_regdmn_init_channels: c 5280 out of range [5490..5850]ol_regdmn_init_channels: c 5320 out of range [5490..5850]Add VHT80 channel: 5210Add VHT80 channel: 5290Add VHT80 channel: 5530ol_regdmn_init_channels: c 5180 out of range [5490..5850]ol_regdmn_init_channels: c 5200 out of range [5490..5850]ol_regdmn_init_channels: c 5220 out of range [5490..5850]ol_regdmn_init_channels: c 5240 out of range [5490..5850]ol_regdmn_init_channels: c 5260 out of range [5490..5850]ol_regdmn_init_channels: c 5280 out of range [5490..5850]ol_regdmn_init_channels: c 5300 out of range [5490..5850]ol_regdmn_init_channels: c 5320 out of range [5490..5850]Skipping VHT80 channel 5580Skipping VHT80 channel 5660Skipping VHT80 channel 5680Skipping VHT80 channel 5700ol_regdmn_init_channels: !avail mode 0x1f9001 (0x200000) flags 0x4000100ol_regdmn_init_channels: !avail mode 0x1f9001 (0x400000) flags 0x8000100freq=106 isCountryCodeValid: EEPROM regdomain 0x0ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2) flags 0x2150ol_regdmn_init_channels: c 5500 out of range [5150..5330]ol_regdmn_init_channels: c 5520 out of range [5150..5330]ol_regdmn_init_channels: c 5540 out of range [5150..5330]ol_regdmn_init_channels: c 5560 out of range [5150..5330]ol_regdmn_init_channels: c 5580 out of range [5150..5330]ol_regdmn_init_channels: c 5660 out of range [5150..5330]ol_regdmn_init_channels: c 5680 out of range [5150..5330]ol_regdmn_init_channels: c 5700 out of range [5150..5330]ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4) flags 0xa0ol_regdmn_init_channels: !avail mode 0x1f9001 (0x8) flags 0xc0ol_regdmn_init_channels: !avail mode 0x1f9001 (0x20) flags 0xd0ol_regdmn_init_channels: !avail mode 0x1f9001 (0x40) flags 0x150ol_regdmn_init_channels: !avail mode 0x1f9001 (0x800) flags 0x10080ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2000) flags 0x20080ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4000) flags 0x40080ol_regdmn_init_channels: c 5500 out of range [5150..5330]ol_regdmn_init_channels: c 5520 out of range [5150..5330]ol_regdmn_init_channels: c 5540 out of range [5150..5330]ol_regdmn_init_channels: c 5560 out of range [5150..5330]ol_regdmn_init_channels: c 5580 out of range [5150..5330]ol_regdmn_init_channels: c 5660 out of range [5150..5330]ol_regdmn_init_channels: c 5680 out of range [5150..5330]ol_regdmn_init_channels: c 5700 out of range [5150..5330]ol_regdmn_init_channels: c 5500 out of range [5150..5330]ol_regdmn_init_channels: c 5540 out of range [5150..5330]ol_regdmn_init_channels: c 5660 out of range [5150..5330]ol_regdmn_init_channels: c 5520 out of range [5150..5330]ol_regdmn_init_channels: c 5560 out of range [5150..5330]ol_regdmn_init_channels: c 5680 out of range [5150..5330]ol_regdmn_init_channels: c 5500 out of range [5150..5330]ol_regdmn_init_channels: c 5520 out of range [5150..5330]ol_regdmn_init_channels: c 5540 out of range [5150..5330]ol_regdmn_init_channels: c 5560 out of range [5150..5330]ol_regdmn_init_channels: c 5580 out of range [5150..5330]ol_regdmn_init_channels: c 5660 out of range [5150..5330]ol_regdmn_init_channels: c 5680 out of range [5150..5330]ol_regdmn_init_channels: c 5700 out of range [5150..5330]ol_regdmn_init_channels: c 5500 out of range [5150..5330]ol_regdmn_init_channels: c 5540 out of range [5150..5330]ol_regdmn_init_channels: c 5660 out of range [5150..5330]ol_regdmn_init_channels: c 5520 out of range [5150..5330]ol_regdmn_init_channels: c 5560 out of range [5150..5330]ol_regdmn_init_channels: c 5680 out of range [5150..5330]Add VHT80 channel: 5210Add VHT80 channel: 5290Add VHT80 channel: 5530ol_regdmn_init_channels: c 5500 out of range [5150..5330]ol_regdmn_init_channels: c 5520 out of range [5150..5330]ol_regdmn_init_channels: c 5540 out of range [5150..5330]ol_regdmn_init_channels: c 5560 out of range [5150..5330]ol_regdmn_init_channels: c 5580 out of range [5150..5330]ol_regdmn_init_channels: c 5660 out of range [5150..5330]ol_regdmn_init_channels: c 5680 out of range [5150..5330]ol_regdmn_init_channels: c 5700 out of range [5150..5330]ol_regdmn_init_channels: !avail mode 0x1f9001 (0x200000) flags 0x4000100ol_regdmn_init_channels: !avail mode 0x1f9001 (0x400000) flags 0x8000100freq=58 isCountryCodeValid: EEPROM regdomain 0x0ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2) flags 0x2150ol_regdmn_init_channels: c 5500 out of range [5150..5330]ol_regdmn_init_channels: c 5520 out of range [5150..5330]ol_regdmn_init_channels: c 5540 out of range [5150..5330]ol_regdmn_init_channels: c 5560 out of range [5150..5330]ol_regdmn_init_channels: c 5580 out of range [5150..5330]ol_regdmn_init_channels: c 5660 out of range [5150..5330]ol_regdmn_init_channels: c 5680 out of range [5150..5330]ol_regdmn_init_channels: c 5700 out of range [5150..5330]ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4) flags 0xa0ol_regdmn_init_channels: !avail mode 0x1f9001 (0x8) flags 0xc0ol_regdmn_init_channels: !avail mode 0x1f9001 (0x20) flags 0xd0ol_regdmn_init_channels: !avail mode 0x1f9001 (0x40) flags 0x150ol_regdmn_init_channels: !avail mode 0x1f9001 (0x800) flags 0x10080ol_regdmn_init_channels: !avail mode 0x1f9001 (0x2000) flags 0x20080ol_regdmn_init_channels: !avail mode 0x1f9001 (0x4000) flags 0x40080ol_regdmn_init_channels: c 5500 out of range [5150..5330]ol_regdmn_init_channels: c 5520 out of range [5150..5330]ol_regdmn_init_channels: c 5540 out of range [5150..5330]ol_regdmn_init_channels: c 5560 out of range [5150..5330]ol_regdmn_init_channels: c 5580 out of range [5150..5330]ol_regdmn_init_channels: c 5660 out of range [5150..5330]ol_regdmn_init_channels: c 5680 out of range [5150..5330]ol_regdmn_init_channels: c 5700 out of range [5150..5330]ol_regdmn_init_channels: c 5500 out of range [5150..5330]ol_regdmn_init_channels: c 5540 out of range [5150..5330]ol_regdmn_init_channels: c 5660 out of range [5150..5330]ol_regdmn_init_channels: c 5520 out of range [5150..5330]ol_regdmn_init_channels: c 5560 out of range [5150..5330]ol_regdmn_init_channels: c 5680 out of range [5150..5330]ol_regdmn_init_channels: c 5500 out of range [5150..5330]ol_regdmn_init_channels: c 5520 out of range [5150..5330]ol_regdmn_init_channels: c 5540 out of range [5150..5330]ol_regdmn_init_channels: c 5560 out of range [5150..5330]ol_regdmn_init_channels: c 5580 out of range [5150..5330]ol_regdmn_init_channels: c 5660 out of range [5150..5330]ol_regdmn_init_channels: c 5680 out of range [5150..5330]ol_regdmn_init_channels: c 5700 out of range [5150..5330]ol_regdmn_init_channels: c 5500 out of range [5150..5330]ol_regdmn_init_channels: c 5540 out of range [5150..5330]ol_regdmn_init_channels: c 5660 out of range [5150..5330]ol_regdmn_init_channels: c 5520 out of range [5150..5330]ol_regdmn_init_channels: c 5560 out of range [5150..5330]ol_regdmn_init_channels: c 5680 out of range [5150..5330]Add VHT80 channel: 5210Add VHT80 channel: 5290Add VHT80 channel: 5530ol_regdmn_init_channels: c 5500 out of range [5150..5330]ol_regdmn_init_channels: c 5520 out of range [5150..5330]ol_regdmn_init_channels: c 5540 out of range [5150..5330]ol_regdmn_init_channels: c 5560 out of range [5150..5330]ol_regdmn_init_channels: c 5580 out of range [5150..5330]ol_regdmn_init_channels: c 5660 out of range [5150..5330]ol_regdmn_init_channels: c 5680 out of range [5150..5330]ol_regdmn_init_channels: c 5700 out of range [5150..5330]ol_regdmn_init_channels: !avail mode 0x1f9001 (0x200000) flags 0x4000100ol_regdmn_init_channels: !avail mode 0x1f9001 (0x400000) flags 0x8000100freq=58 [wifi2] FWLOG: [24124] WAL_DBGID_TX_AC_BUFFER_SET ( 0x3, 0x1e, 0x94c, 0x94c, 0x0 )[wifi2] FWLOG: [24124] WAL_DBGID_TX_AC_BUFFER_SET ( 0x12, 0x1e, 0x94c, 0x94c, 0x0 )[wifi2] FWLOG: [24124] WAL_DBGID_TX_AC_BUFFER_SET ( 0x45, 0x1e, 0x94c, 0x94c, 0x0 )[wifi2] FWLOG: [24124] WAL_DBGID_TX_AC_BUFFER_SET ( 0x67, 0x1e, 0x94c, 0x94c, 0x0 )[wifi2] FWLOG: [24124] WAL_DBGID_TX_AC_BUFFER_SET ( 0x100, 0x11e1a300 )[wifi2] FWLOG: [24223] WAL_DBGID_PDEV_INFO_PRINT ( 0x3a, 0xa10, 0x160, 0x10, 0x0 )[wifi2] FWLOG: [24223] WAL_DBGID_PDEV_INFO_PRINT ( 0x3a, 0x10, 0x0, 0x10, 0x12 )[wifi2] FWLOG: [24665] WAL_DBGID_PDEV_INFO_PRINT ( 0x37, 0x199[wifi0] FWLOG: [49413] WAL_DBGID_PDEV_INFO_PRINT ( 0x37, 0x199, 0x130, 0x0, 0x32 ), 0x130, 0x30, 0x0 )[wifi2] FWLOG: [24665] WAL_DBGID_PDEV_INFO_PRINT ( 0x37, 0x30, 0x0, 0x30, 0x0 )[wifi2] FWLOG: [24741] WAL_DBGID_PDEV_INFO_PRINT ( 0x37, 0x199, 0x130, 0x30, 0x0 )[wifi2] FWLOG: [24741] WAL_DBGID_PDEV_INFO_PRINT ( 0x37, 0x30, 0x0, 0x30, 0x0 )[wifi1] FWLOG: [49499] WAL_DBGID_PDEV_INFO_PRINT ( 0x37, 0x199, 0x130, 0x30, 0x0 )[wifi1] FWLOG: [49499] WAL_DBGID_PDEV_INFO_PRINT ( 0x37, 0x30, 0x0, 0x30, 0x0 )wlan_vap_create : enter. devhandle=0xcdf804c0, opmode=IEEE80211_M_HOSTAP, flags=0x1send_vdev_create_cmd_non_tlv: ID = 0 Type = 1, Subtype = 0 VAP Addr = 10:7b:44:XX:XX:XX:ieee80211_mbo_vattach:MBO Initialized ieee80211_oce_vattach: OCE Initialized wlan_vap_create : exit. devhandle=0xcdf804c0, vap=0xcb1a8000, opmode=IEEE80211_M_HOSTAP, flags=0x1.__ieee80211_smart_ant_init: Smart Antenna functions are not registered !!! Enabling TX checksum bit for the vap ath0 features 4000 Enabling SG bit for the vap ath0 features 4000 Enabling SG bit for the vap ath0 features 4000 Enabling TSO bit for the vap ath0 features 4000 Enabling LRO bit for the vap ath0 features 4000 VAP device ath0 created osifp: (cf3facc0) os_if: (cb1a8000)Switching to Tx Mode-1 Threshold 280wlan_vap_create : enter. devhandle=0xcd2804c0, opmode=IEEE80211_M_HOSTAP, flags=0x1send_vdev_create_cmd_non_tlv: ID = 0 Type = 1, Subtype = 0 VAP Addr = 10:7b:44:XX:XX:XX:ieee80211_mbo_vattach:MBO Initialized ieee80211_oce_vattach: OCE Initialized wlan_vap_create : exit. devhandle=0xcd2804c0, vap=0xcb1b8000, opmode=IEEE80211_M_HOSTAP, flags=0x1.__ieee80211_smart_ant_init: Smart Antenna functions are not registered !!! Enabling TX checksum bit for the vap ath1 features 4000 Enabling SG bit for the vap ath1 features 4000 Enabling SG bit for the vap ath1 features 4000 Enabling TSO bit for the vap ath1 features 4000 Enabling LRO bit for the vap ath1 features 4000 VAP device ath1 created osifp: (cf3fccc0) os_if: (cb1b8000)wlan_vap_create : enter. devhandle=0xcc0c04c0, opmode=IEEE80211_M_HOSTAP, flags=0x1send_vdev_create_cmd_non_tlv: ID = 0 Type = 1, Subtype = 0 VAP Addr = 10:7b:44:XX:XX:XX:ieee80211_mbo_vattach:MBO Initialized ieee80211_oce_vattach: OCE Initialized wlan_vap_create : exit. devhandle=0xcc0c04c0, vap=0xcb5e8000, opmode=IEEE80211_M_HOSTAP, flags=0x1.__ieee80211_smart_ant_init: Smart Antenna functions are not registered !!! Enabling TX checksum bit for the vap ath2 features 4000 Enabling SG bit for the vap ath2 features 4000 Enabling SG bit for the vap ath2 features 4000 Enabling TSO bit for the vap ath2 features 4000 Enabling LRO bit for the vap ath2 features 4000 VAP device ath2 created osifp: (cf3fecc0) os_if: (cb5e8000)UBIFS: background thread "ubifs_bgt0_5" started, PID 390UBIFS: recovery neededUBIFS: recovery completedUBIFS: mounted UBI device 0, volume 5, name "jffs2"UBIFS: LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytesUBIFS: FS size: 17649664 bytes (16 MiB, 139 LEBs), journal size 2666496 bytes (2 MiB, 21 LEBs)UBIFS: reserved for root: 0 bytes (0 KiB)UBIFS: media format: w4/r0 (latest is w4/r0), UUID E92FXXXX-XXXX-XXXX-XXXX-XXXXXXXXXXXX, small LPT modelusbcore: registered new interface driver usbfsusbcore: registered new interface driver hubusbcore: registered new device driver usbehci_hcd: USB 2.0 'Enhanced' Host Controller (EHCI) Driverohci_hcd: USB 1.1 'Open' Host Controller (OHCI) Driverxhci-hcd xhci-hcd.0.auto: xHCI Host Controllerxhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1xhci-hcd xhci-hcd.0.auto: ## USB3 port 0/1 addr(d3830430) s1(000002a0) --> (000002a0)xhci-hcd xhci-hcd.0.auto: irq 164, io mem 0x08a00000hub 1-0:1.0: USB hub foundhub 1-0:1.0: 1 port detectedxhci-hcd xhci-hcd.0.auto: xHCI Host Controllerxhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2hub 2-0:1.0: USB hub foundhub 2-0:1.0: 1 port detectedxhci-hcd xhci-hcd.1.auto: xHCI Host Controllerxhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3xhci-hcd xhci-hcd.1.auto: irq 168, io mem 0x06000000hub 3-0:1.0: USB hub foundhub 3-0:1.0: 1 port detectedxhci-hcd xhci-hcd.1.auto: xHCI Host Controllerxhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4hub 4-0:1.0: USB hub foundhub 4-0:1.0: config failed, hub doesn't have any ports! (err -19)xhci-hcd xhci-hcd.1.auto: remove, state 4usb usb4: USB disconnect, device number 1xhci-hcd xhci-hcd.1.auto: Host not halted after 16000 microseconds.xhci-hcd xhci-hcd.1.auto: USB bus 4 deregisteredxhci-hcd xhci-hcd.1.auto: remove, state 1usb usb3: USB disconnect, device number 1xhci-hcd xhci-hcd.1.auto: Host not halted after 16000 microseconds.xhci-hcd xhci-hcd.1.auto: Host controller not halted, aborting reset.xhci-hcd xhci-hcd.1.auto: USB bus 3 deregisteredxhci-hcd xhci-hcd.0.auto: remove, state 1usb usb2: USB disconnect, device number 1xhci-hcd xhci-hcd.0.auto: Host not halted after 16000 microseconds.xhci-hcd xhci-hcd.0.auto: USB bus 2 deregisteredxhci-hcd xhci-hcd.0.auto: remove, state 1usb usb1: USB disconnect, device number 1xhci-hcd xhci-hcd.0.auto: Host not halted after 16000 microseconds.xhci-hcd xhci-hcd.0.auto: Host controller not halted, aborting reset.xhci-hcd xhci-hcd.0.auto: USB bus 1 deregisteredxhci-hcd xhci-hcd.0.auto: xHCI Host Controllerxhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1xhci-hcd xhci-hcd.0.auto: ## USB3 port 0/1 addr(d3860430) s1(000002a0) --> (000002a0)xhci-hcd xhci-hcd.0.auto: irq 164, io mem 0x08a00000hub 1-0:1.0: USB hub foundhub 1-0:1.0: 1 port detectedxhci-hcd xhci-hcd.0.auto: xHCI Host Controllerxhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2hub 2-0:1.0: USB hub foundhub 2-0:1.0: 1 port detectedxhci-hcd xhci-hcd.1.auto: xHCI Host Controllerxhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3xhci-hcd xhci-hcd.1.auto: irq 168, io mem 0x06000000hub 3-0:1.0: USB hub foundhub 3-0:1.0: 1 port detectedxhci-hcd xhci-hcd.1.auto: xHCI Host Controllerxhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4hub 4-0:1.0: USB hub foundhub 4-0:1.0: config failed, hub doesn't have any ports! (err -19)usb 3-1: new full-speed USB device number 2 using xhci-hcddevice eth1 entered promiscuous modedevice ath0 entered promiscuous modedevice ath1 entered promiscuous modedevice ath2 entered promiscuous modeIPv6: ADDRCONF(NETDEV_UP): br0: link is not readybr0: port 1(eth1) entered listening statebr0: port 1(eth1) entered listening stateol_wifi_assoc_netlink_receive: WiFi assoc/disassoc events being sent to PID:597br0: port 1(eth1) entered learning statesu bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1[DEBUG] vap-0(ath0):set SIOC80211NWID, 4 characters DES SSID SET=lyra br0: port 2(ath0) entered listening statebr0: port 2(ath0) entered listening state8021q: adding VLAN 0 to HW filter on device ath0[wifi0] FWLOG: [63703] WAL_DBGID_PDEV_INFO_PRINT ( 0x2, 0x0 )[wifi0] FWLOG: [63777] WAL_DBGID_RST_STATS ( 0x6, 0x2, 0x96c, 0x0 )[wifi0] FWLOG: [63777] WAL_DBGID_DEV_RESET ( 0xc01d, 0x3a5 )[wifi0] FWLOG: [63829] WAL channel change freq=2412, mode=1 flags=0 rx_ok=1 tx_ok=1[wifi0] FWLOG: [64137] WAL channel change freq=2417, mode=1 flags=0 rx_ok=1 tx_ok=1br0: topology change detected, propagatingbr0: port 1(eth1) entered forwarding stateIPv6: ADDRCONF(NETDEV_CHANGE): br0: link becomes ready ieee80211_ioctl_siwmode: imr.ifm_active=131712, new mode=3, valid=1 [UNSPECIFIED] ol_scan_unregister_event_handler: Failed to unregister evhandler=bf5dce18 arg=ccd80000osif_vap_stop: Scan in progress.. Cancelling it. vap: 0xcb1a8000 br0: port 2(ath0) entered disabled state DEVICE IS DOWN ifname=ath0 DEVICE IS DOWN ifname=ath0br0: port 2(ath0) entered listening statebr0: port 2(ath0) entered listening state8021q: adding VLAN 0 to HW filter on device ath0su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1[DEBUG] vap-0(ath1):set SIOC80211NWID, 9 characters DES SSID SET=lyra_5G-2 br0: port 3(ath1) entered listening statebr0: port 3(ath1) entered listening state8021q: adding VLAN 0 to HW filter on device ath1 ieee80211_ioctl_siwmode: imr.ifm_active=66176, new mode=3, valid=1 [UNSPECIFIED] ol_scan_unregister_event_handler: Failed to unregister evhandler=bf5dce18 arg=cc380000osif_vap_stop: Scan in progress.. Cancelling it. vap: 0xcb1b8000 br0: port 3(ath1) entered disabled state DEVICE IS DOWN ifname=ath1 DEVICE IS DOWN ifname=ath1[wifi0] FWLOG: [64452] WAL channel change freq=2422, mode=1 flags=0 rx_ok=1 tx_ok=1[wifi0] FWLOG: [64502] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 )[wifi0] FWLOG: [64502] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 )[wifi0] FWLOG: [64779] WAL_DBGID_SECURITY_ENCR_EN ( )[wifi0] FWLOG: [64779] WAL_DBGID_SECURITY_MCAST_KEY_SET ( 0x1 )[wifi0] FWLOG: [64806] WAL channel change freq=2412, mode=1 flags=0 rx_ok=1 tx_ok=1[wifi0] FWLOG: [65121] WAL channel change freq=2417, mode=1 flags=0 rx_ok=1 tx_ok=1xhci-hcd xhci-hcd.1.auto: remove, state 4usb usb4: USB disconnect, device number 1xhci-hcd xhci-hcd.1.auto: Host not halted after 16000 microseconds.xhci-hcd xhci-hcd.1.auto: USB bus 4 deregisteredxhci-hcd xhci-hcd.1.auto: remove, state 1usb usb3: USB disconnect, device number 1usb 3-1: USB disconnect, device number 2br0: port 3(ath1) entered listening statebr0: port 3(ath1) entered listening state8021q: adding VLAN 0 to HW filter on device ath1[wifi1] FWLOG: [64902] WAL_DBGID_PDEV_INFO_PRINT ( 0x2, 0x0 )[wifi1] FWLOG: [64955] WAL_DBGID_RST_STATS ( 0x6, 0x2, 0x1464, su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1[wifi1] su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1FWLOG: [64955] WAL_DBGID_DEV_RESET ( 0xc01d[DEBUG] vap-0(ath2):set SIOC80211NWID, 9 characters DES SSID SET=lyra_5G-1 , 0x3bc )[wifi1] FWLOG: [65017] WAL channel change freq=5500, mode=0 flags=0 rx_ok=1 tx_ok=1[wifi1] FWLOG: [65127] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 )[wifi1] FWLOG: [65127] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 )[wifi1] FWLOG: [65445] WAL_DBGID_SECURITY_ENCR_EN ( )[wifi1] FWLOG: [65445] WAL_DBGID_SECURITY_MCAST_KEY_SET ( 0x1 )br0: port 4(ath2) entered listening statebr0: port 4(ath2) entered listening state8021q: adding VLAN 0 to HW filter on device ath2 ieee80211_ioctl_siwmode: imr.ifm_active=66176, new mode=3, valid=1 [UNSPECIFIED] ol_scan_unregister_event_handler: Failed to unregister evhandler=bf5dce18 arg=cb180000osif_vap_stop: Scan in progress.. Cancelling it. vap: 0xcb5e8000 br0: port 4(ath2) entered disabled state DEVICE IS DOWN ifname=ath2 DEVICE IS DOWN ifname=ath2br0: port 4(ath2) entered listening statebr0: port 4(ath2) entered listening state8021q: adding VLAN 0 to HW filter on device ath2siwfreqSet freq vap 0 stop send + cb1a8000[UNSPECIFIED] ol_scan_unregister_event_handler: Failed to unregister evhandler=bf5dce18 arg=ccd80000osif_vap_acs_cancel: Scan in progress.. Cancelling it vap: 0xcb1a8000Set freq vap 0 stop send -cb1a8000Set wait done --cb1a8000[wifi2] FWLOG: [40694] WAL_DBGID_PDEV_INFO_PRINT ( 0x2, 0x0 )[wifi2] FWLOG: [40744] WAL_DBGID_DEV_RESET ( 0xc01d, 0x43b )[wifi2] FWLOG: [40804] WAL channel change freq=5180, mode=0 flags=0 rx_ok=1 tx_ok=1[wifi2] FWLOG: [40914] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0siwfreqSet freq vap 0 stop send + cb5e8000[UNSPECIFIED] ol_scan_unregister_event_handler: Failed to unregister evhandler=bf5dce18 arg=cb180000osif_vap_acs_cancel: Scan in progress.. Cancelling it vap: 0xcb5e8000Set freq vap 0 stop send -cb5e8000[wifi0] FWLOG: [65435] WAL channel change freq=2422, mode=1 flags=0 rx_ok=1 tx_ok=1[wifi0] FWLOG: [65750] WAL channel change freq=2427, mode=1 flags=0 rx_ok=1 tx_ok=1[wifi0] FWLOG: [66063] WAL channel change freq=2432, mode=1 flags=0 rx_ok=1 tx_ok=1[wifi0] FWLOG: [66145] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 )[wifi0] FWLOG: [66145] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 )[wifi0] FWLOG: [66210] WAL channel change freq=2412, mode=1 flags=0 rx_ok=1 tx_ok=1Set wait done --cb5e8000[wifi2] FWLOG: [40914] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 )[wifi2] FWLOG: [41170] WAL_DBGID_SECURITY_ENCR_EN ( )[wifi2] FWLOG: [41170] WAL_DBGID_SECURITY_MCAST_KEY_SET ( siwfreqSet freq vap 0 stop send + cb1b8000[UNSPECIFIED] ol_scan_unregister_event_handler: Failed to unregister evhandler=bf5dce18 arg=cc380000osif_vap_acs_cancel: Scan in progress.. Cancelling it vap: 0xcb1b8000Set freq vap 0 stop send -cb1b80000x1Set wait done --cb1b8000[wifi1] FWLOG: [65787] WAL channel change freq=5520, mode=0 flags=0 rx_ok=1 tx_ok=1[wifi1] FWLOG: [66102] WAL channel change freq=5540, mode=0 flags=0 rx_ok=1 tx_ok=1[wifi1] FWLOG: [66316] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 )[wifi1] FWLOG: [66316] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 )[wifi1] FWLOG: [66374] WAL channel change freq=5500, mode=0 flags=0 rx_ok=1 tx_ok=1br0: port 2(ath0) entered learning state[wifi2] FWLOG: [41336] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 )[wifi2] FWLOG: [41336] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 )[wifi2] FWLOG: [41685] WAL channel change freq=5200, mode=0 flags=0 rx_ok=1 tx_ok=1[wifi2] FWLOG: [42000] WAL channel change freq=5220, mode=0 flags=0 rx_ok=1 tx_ok=1[wifi2] FWLOG: [42314] WAL channel change freq=5240, mode=0 flags=0 rx_ok=1 tx_ok=1[wifi0] FWLOG: [66524] WAL channel change freq=2417, mode=1 flags=0 rx_ok=1 tx_ok=1[wifi0] FWLOG: [66839] WAL channel change freq=2422, mode=1 flags=0 rx_ok=1 tx_ok=1[wifi0] FWLOG: [67153] WAL channel change freq=2427, mode=1 flags=0 rx_ok=1 tx_ok=1br0: port 3(ath1) entered learning state[wifi1] FWLOG: [66689] WAL channel change freq=5520, mode=0 flags=0 rx_ok=1 tx_ok=1[wifi1] FWLOG: [67004] WAL channel change freq=5540, mode=0 flags=0 rx_ok=1 tx_ok=1[wifi1] FWLOG: [67318] WAL channel change freq=5560, mode=0 flags=0 rx_ok=1 tx_ok=1[wifi1] FWLOG: [67633] WAL channel change freq=5580, mode=0 flags=0 rx_ok=1 tx_ok=1br0: port 4(ath2) entered learning state[wifi2] FWLOG: [42628] WAL channel change freq=5260, mode=0 flags=0 rx_ok=1 tx_ok=1[wifi2] FWLOG: [42942] WAL channel change freq=5280, mode=0 flags=0 rx_ok=1 tx_ok=1[wifi2] FWLOG: [43256] WAL channel change freq=5300, mode=0 flags=0 rx_ok=1 tx_ok=1[wifi0] FWLOG: [67467] WAL channel change freq=2432, mode=1 flags=0 rx_ok=1 tx_ok=1[wifi0] FWLOG: [67781] WAL channel change freq=2437, mode=1 flags=0 rx_ok=1 tx_ok=1[wifi0] FWLOG: [68096] WAL channel change freq=2442, mode=1 flags=0 rx_ok=1 tx_ok=1nf_conntrack_rtsp v0.7 loadingnf_nat_rtsp v0.7 loading[wifi1] FWLOG: [67947] WAL channel change freq=5660, mode=0 flags=0 rx_ok=1 tx_ok=1[wifi1] FWLOG: [68261] WAL channel change freq=5680, mode=0 flags=0 rx_ok=1 tx_ok=1[wifi1] FWLOG: [68576] WAL channel change freq=5700, mode=0 flags=0 rx_ok=1 tx_ok=1---- ACS CALCULATE ---- Chan 52 pre_param 15 param 322 Chan 56 pre_param 11 param 318 Chan 60 pre_param 9 param 316 Chan 64 pre_param 7 param 314 Selected dot11 channel 60 OL vap_start +VDEV STARTOL vap_start -ol_ath_vap_set_param: Now supported MGMT RATE is 6000(kbps) and rate code: 0x3---- ACS CALCULATE ---- Chan 108 pre_param 119 param 119 Selected dot11 channel 108 OL vap_start +VDEV STARTOL vap_start -ol_ath_vap_set_param: Now supported MGMT RATE is 6000(kbps) and rate code: 0x3br0: topology change detected, propagatingbr0: port 2(ath0) entered forwarding stateol_vdev_start_resp_ev for vap 0 (ccac6000)send_wmm_update_cmd_non_tlv:ol_if_dfs_configure: calledol_if_dfs_configure: ETSI domainol_if_dfs_disable: calledol_if_dfs_enable: calledol_vdev_start_resp_ev for vap 0 (cd350000)send_wmm_update_cmd_non_tlv:ol_if_dfs_configure: calledol_if_dfs_configure: ETSI domainol_if_dfs_disable: calledol_if_dfs_enable: called[wifi2] FWLOG: [43571] WAL channel change freq=5320, mode=0 flags=0 rx_ok=1 tx_ok=1[wifi2] FWLOG: [43884] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 )[wifi2] FWLOG: [43884] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 )[wifi2] FWLOG: [43902] vap-0 VDEV_MGR_VDEV_START ( 0x14b4, 0x2, 0x0, 0x1 )[wifi2] FWLOG: [43903] WAL channel change freq=5300, mode=10 flags=0 rx_ok=1 tx_ok=1[wifi2] [wifi0] FWLOG: [68409] WAL channel change freq=2447, mode=1 flags=0 rx_ok=1 tx_ok=1[wifi0] FWLOG: [68724] WAL channel change freq=2452, mode=1 flags=0 rx_ok=1 tx_ok=1[wifi0] FWLOG: [69038] WAL channel change freq=2457, mode=1 flags=0 rx_ok=1 tx_ok=1FWLOG: [44111] VDEV_MGR_VDEV_START_RESP ( 0x0 )br0: topology change detected, propagatingbr0: port 3(ath1) entered forwarding state[wifi1] FWLOG: [68890] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 )[wifi1] FWLOG: [68890] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 )[wifi1] FWLOG: [68898] vap-0 VDEV_MGR_VDEV_START ( 0x15a4, 0x2, 0x0, 0x1 )[wifi1] FWLOG: [68898] WAL channel change freq=5540, mode=10 flags=0 rx_ok=1 tx_ok=1[wifi1] FWLOG: [68898] WAL_DBGID_RST_STATS ( 0x2, 0x80, 0x15a4, 0x1 )[wifi1] FWLOG: [69082] VDEV_MGR_VDEV_START_RESP ( 0x0 )br0: topology change detected, propagatingbr0: port 4(ath2) entered forwarding state---- ACS CALCULATE ---- Chan 6 pre_param 44 param 44 Chan 11 pre_param 40 param 40 Best Channel Selected 11OL vap_start +VDEV STARTOL vap_start -ol_ath_vap_set_param: Now supported MGMT RATE is 1000(kbps) and rate code: 0x43xhci-hcd xhci-hcd.1.auto: Timeout while waiting for configure endpoint commandxhci-hcd xhci-hcd.1.auto: Host not halted after 16000 microseconds.xhci-hcd xhci-hcd.1.auto: Host controller not halted, aborting reset.xhci-hcd xhci-hcd.1.auto: USB bus 3 deregisteredxhci-hcd xhci-hcd.0.auto: remove, state 4usb usb2: USB disconnect, device number 1xhci-hcd xhci-hcd.0.auto: Host not halted after 16000 microseconds.xhci-hcd xhci-hcd.0.auto: USB bus 2 deregisteredxhci-hcd xhci-hcd.0.auto: remove, state 4usb usb1: USB disconnect, device number 1ol_vdev_start_resp_ev for vap 0 (cf012000)send_wmm_update_cmd_non_tlv:su bfee 1 mu bfee 0 su bfer 1 mu bfer 1 impl bf 0 sounding dim 1send_vdev_up_cmd_non_tlv for vap 0xhci-hcd xhci-hcd.0.auto: Host not halted after 16000 microseconds.xhci-hcd xhci-hcd.0.auto: Host controller not halted, aborting reset.xhci-hcd xhci-hcd.0.auto: USB bus 1 deregisteredBeacon mode set to staggered. Cannot enable FD__ieee80211_smart_ant_init: Smart Antenna functions are not registered !!! [wifi0] FWLOG: [69352] WAL channel change freq=2462, mode=1 flags=0 rx_ok=1 tx_ok=1[wifi0] FWLOG: [69667] WAL channel change freq=2467, mode=1 flags=0 rx_ok=1 tx_ok=1[wifi0] FWLOG: [69981] WAL channel change freq=2472, mode=1 flags=0 rx_ok=1 tx_ok=1[wifi0] FWLOG: [70294] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 )[wifi0] FWLOG: [70294] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 )[wifi0] FWLOG: [70305] vap-0 VDEV_MGR_VDEV_START ( 0x99e, 0x2, 0x0, 0x0 )[wifi0] FWLOG: [70305] WAL channel change freq=2462, mode=7 flags=0 rx_ok=1 tx_ok=1[wifi0] FWLOG: [70305] WAL_DBGID_RST_STATS ( 0x2, 0x80, 0x99e, 0x1 )xhci-hcd xhci-hcd.0.auto: xHCI Host Controllerxhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1xhci-hcd xhci-hcd.0.auto: ## USB3 port 0/1 addr(d3df0430) s1(000002a0) --> (000002a0)xhci-hcd xhci-hcd.0.auto: irq 164, io mem 0x08a00000hub 1-0:1.0: USB hub foundhub 1-0:1.0: 1 port detectedxhci-hcd xhci-hcd.0.auto: xHCI Host Controllerxhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2hub 2-0:1.0: USB hub foundhub 2-0:1.0: 1 port detectedxhci-hcd xhci-hcd.1.auto: xHCI Host Controllerxhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 3xhci-hcd xhci-hcd.1.auto: irq 168, io mem 0x06000000hub 3-0:1.0: USB hub foundhub 3-0:1.0: 1 port detectedxhci-hcd xhci-hcd.1.auto: xHCI Host Controllerxhci-hcd xhci-hcd.1.auto: new USB bus registered, assigned bus number 4hub 4-0:1.0: USB hub foundhub 4-0:1.0: config failed, hub doesn't have any ports! (err -19)usbcore: registered new interface driver btusbusbcore: registered new interface driver ath3k[wifi0] FWLOG: [70493] VDEV_MGR_VDEV_START_RESP ( 0x0 )[wifi0] FWLOG: [70514] VDEV_MGR_HP_START_TIME ( 0x0, 0x99e, 0x19af000 )[wifi0] FWLOG: [70514] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x1 )[wifi0] FWLOG: [70514] RESMGR_OCS_GEN_PERIODIC_NOA ( 0x0 )[wifi0] FWLOG: [70514] VDEV_MGR_AP_TBTT_CONFIG ( 0x0, 0x99e, 0x0, 0x0 )usb 3-1: new full-speed USB device number 2 using xhci-hcdusb 3-1: Direct firmware load failed with error 0usb 3-1: Falling back to user helperusb 3-1: Firmware loaded from user helper succesfullyusb 3-1: Direct firmware load failed with error 0usb 3-1: Falling back to user helperusb 3-1: Firmware loaded from user helper succesfullyusb 3-1: USB disconnect, device number 2usb 3-1: new full-speed USB device number 3 using xhci-hcdusb 3-1: device descriptor read/64, error -110xhci-hcd xhci-hcd.1.auto: Setup ERROR: setup context command for slot 1.usb 3-1: new full-speed USB device number 4 using xhci-hcd

Format: Log Type - Time(microsec) - Message - Optional InfoLog Type: B - Since Boot(Power On Reset), D - Delta, S - StatisticS - QC_IMAGE_VERSION_STRING=BOOT.BF.3.1.1-00110S - IMAGE_VARIANT_STRING=DAACANAZAS - OEM_IMAGE_VERSION_STRING=CRMS - Boot Config, 0x00000025S - Reset status Config, 0x00000010S - Core 0 Frequency, 0 MHzB - 261 - PBL, StartB - 1338 - bootable_media_detect_entry, StartB - 2608 - bootable_media_detect_success, StartB - 2622 - elf_loader_entry, StartB - 4028 - auth_hash_seg_entry, StartB - 6178 - auth_hash_seg_exit, StartB - 74217 - elf_segs_hash_verify_entry, StartB - 196008 - PBL, EndB - 196032 - SBL1, StartB - 288049 - pm_device_init, StartD - 7 - pm_device_init, DeltaB - 289540 - boot_flash_init, StartD - 74297 - boot_flash_init, DeltaB - 368139 - boot_config_data_table_init, StartD - 13971 - boot_config_data_table_init, Delta - (419 Bytes)B - 384860 - clock_init, StartD - 7583 - clock_init, DeltaB - 395878 - CDT version:2,Platform ID:8,Major ID:1,Minor ID:0,Subtype:1B - 399292 - sbl1_ddr_set_params, StartB - 404387 - cpr_init, StartD - 2 - cpr_init, DeltaB - 408769 - Pre_DDR_clock_init, StartD - 4 - Pre_DDR_clock_init, DeltaD - 13172 - sbl1_ddr_set_params, DeltaB - 422074 - pm_driver_init, StartD - 2 - pm_driver_init, DeltaB - 492044 - sbl1_wait_for_ddr_training, StartD - 28 - sbl1_wait_for_ddr_training, DeltaB - 507587 - Image Load, StartD - 143910 - QSEE Image Loaded, Delta - (268920 Bytes)B - 651924 - Image Load, StartD - 2120 - SEC Image Loaded, Delta - (2048 Bytes)B - 662067 - Image Load, StartD - 198697 - APPSBL Image Loaded, Delta - (472859 Bytes)B - 861159 - QSEE Execution, StartD - 56 - QSEE Execution, DeltaB - 867366 - SBL1, EndD - 673444 - SBL1, DeltaS - Flash Throughput, 2099 KB/s (744246 Bytes, 354446 us)S - DDR Frequency, 672 MHzU-Boot 2012.07-06585-ga52dc0d-dirty [local,local] (Mar 09 2017 - 11:28:27)HIVE bootloader version: 1.0.0.2smem ram ptable found: ver: 1 len: 3ASUS HIVE gpio init : wps / reset pinRAM Configuration:Bank #0: 80000000 256 MiBmachid : 0x8010001Maximum malloc length: 4096 KBytesmem_malloc_start/brk/end: 0x86ed0000/86ed0000/872f0000Relocation offset: 0NAND: ID = 9580f1c2Vendor = c2Device = f1ONFI device foundSF NAND unsupported id:ff:ff:ff:ffSF: Unsupported manufacturer ffipq_spi: SPI Flash not found (bus/cs/speed/mode) = (0/0/48000000/0)128 MiB*** Warning - bad CRC, using default environmentPCI0 Link IntializedIn: serialOut: serialErr: serialCheck bootloader area ... name : offset size 0:SBL1 : 00000000 000800000:MIBIB : 00080000 000800000:QSEE : 00100000 001000000:CDT : 00200000 000800000:APPSBL : 00280000 001400000:APPSBLENV : 003c0000 00040000machid: 8010001flash_type: 2Set ENGX pattern failed !!LP5523 Chip addresses: 32 Creating 1 MTD partitions on "nand0":0x00400000-0x08000000 : "mtd=2"UBI: attaching mtd1 to ubi0UBI: physical eraseblock size: 131072 bytes (128 KiB)UBI: logical eraseblock size: 126976 bytesUBI: smallest flash I/O unit: 2048UBI: VID header offset: 2048 (aligned 2048)UBI: data offset: 4096UBI: max. sequence number: 78095UBI: attached mtd1 to ubi0UBI: MTD device name: "mtd=2"UBI: MTD device size: 124 MiBUBI: number of good PEBs: 991UBI: number of bad PEBs: 1UBI: number of corrupted PEBs: 0UBI: max. allowed volumes: 128UBI: wear-leveling threshold: 4096UBI: number of internal volumes: 1UBI: number of user volumes: 8UBI: available PEBs: 10UBI: total number of reserved PEBs: 981UBI: number of PEBs reserved for bad PEB handling: 9UBI: max/mean erase counter: 169/79UBI: image sequence number: 2108563064UBI: vol_id reserved_pebs alignment data_pad vol_type usable_leb_size used_ebs used_bytes last_eb_bytes corrupted upd_marker name_len nameUBI: 0 3 1 0 dynamic 1f000 3 5d000 1f000 0 0 5 nvramUBI: 1 1 1 0 dynamic 1f000 1 1f000 1f000 0 0 7 FactoryUBI: 2 1 1 0 dynamic 1f000 1 1f000 1f000 0 0 8 Factory2UBI: 3 17 1 0 dynamic 1f000 17 2c9000 1f000 0 0 5 linuxUBI: 4 18d 1 0 dynamic 1f000 18d 3013000 1f000 0 0 6 linux2UBI: 5 95 1 0 dynamic 1f000 95 120b000 1f000 0 0 5 jffs2UBI: 6 54 1 0 dynamic 1f000 54 a2c000 1f000 0 0 6 rootfsUBI: 7 136 1 0 dynamic 1f000 136 258a000 1f000 0 0 b rootfs_dataUBI: 7fffefff 2 1 0 dynamic 1f000 2 3e000 2 0 0 d layout volumeUBI volume [linux] size 2c9000 smaller than 3013000!Read 0x1f000 bytes from volume [Factory] offset 0x0 to 86eb0ce0EEPROM set 0: OK (version 41)Read 0x1f000 bytes from volume [Factory2] offset 0x0 to 86eb0ce0EEPROM set 1: OK (version 41)Read 0x1f000 bytes from volume [Factory] offset 0x0 to 86ed1850Select EEPROM set 0 at offset 0x0.Please choose the operation: 1: Load System code to SDRAM via TFTP. 2: Load System code then write to Flash via TFTP. 3: Boot System code via Flash (default). 4: Entr boot command line interface. 7: Load Boot Loader code then write to Flash via Serial. 9: Load Boot Loader code then write to Flash via TFTP. 1 0 3: Boot System code via Flash (default).HIVE bootloader version: 1.0.0.2MAC Address: 10:7B:44:XX:XX:X0Read 0x40 bytes from volume [linux] offset 0x0 to 84000000 FIT/FDT format image found at 0x84000000, size 0x002afd84Read 0x2afdc4 bytes from volume [linux] offset 0x0 to 84000000## Booting kernel from FIT Image at 84000000 ... Using 'config@1' configuration Trying 'kernel@1' kernel subimage Description: ARM OpenWrt Linux-4.14.167 Type: Kernel Image Compression: lzma compressed Data Start: 0x840000e4 Data Size: 2797824 Bytes = 2.7 MiB Architecture: ARM OS: Linux Load Address: 0x80208000 Entry Point: 0x80208000 Hash algo: crc32 Hash value: a1ff5169 Hash algo: sha1 Hash value: 69edcdce8ecfb5129717f04ac07450b0f811a079## Flattened Device Tree from FIT Image at 84000000 Using 'config@1' configuration Trying 'fdt@1' FDT blob subimage Description: ARM OpenWrt asus_map-ac2200 device tree blob Type: Flat Device Tree Compression: uncompressed Data Start: 0x842ab320 Data Size: 17777 Bytes = 17.4 KiB Architecture: ARM Hash algo: crc32 Hash value: 518a6ab0 Hash algo: sha1 Hash value: c9d463f04aebef3435401e0e1efac2e3e47afc26 Booting using the fdt blob at 0x842ab320Read 0x28 bytes from volume [linux2] offset 0x0 to 86ecfc38Copy firmware from c049b000 to c34ae000, length 2afdc40x2afdc4 bytes written to volume linux2 Uncompressing Kernel Image ... OK Loading Device Tree to 86ec8000, end 86ecf570 ... OKDevice nand2 not found!Using machid 0x8010001 from environmentStarting kernel ...[ 0.000000] Booting Linux on physical CPU 0x0[ 0.000000] Linux version 4.14.167 (builder@buildhost) (gcc version 7.5.0 (OpenWrt GCC 7.5.0 r10911-c155900f66)) #0 SMP Wed Jan 29 16:05:35 2020[ 0.000000] CPU: ARMv7 Processor [410fc075] revision 5 (ARMv7), cr=10c5387d[ 0.000000] CPU: div instructions available: patching division code[ 0.000000] CPU: PIPT / VIPT nonaliasing data cache, VIPT aliasing instruction cache[ 0.000000] OF: fdt: Machine model: ASUS Lyra MAP-AC2200[ 0.000000] Memory policy: Data cache writealloc[ 0.000000] On node 0 totalpages: 65024[ 0.000000] free_area_init_node: node 0, pgdat c0a24280, node_mem_map cfdf9000[ 0.000000] Normal zone: 512 pages used for memmap[ 0.000000] Normal zone: 0 pages reserved[ 0.000000] Normal zone: 65024 pages, LIFO batch:15[ 0.000000] random: get_random_bytes called from 0xc09008d0 with crng_init=0[ 0.000000] percpu: Embedded 15 pages/cpu s29388 r8192 d23860 u61440[ 0.000000] pcpu-alloc: s29388 r8192 d23860 u61440 alloc=15*4096[ 0.000000] pcpu-alloc: [0] 0 [0] 1 [0] 2 [0] 3 [ 0.000000] Built 1 zonelists, mobility grouping on. Total pages: 64512[ 0.000000] Kernel command line: root_rfs=0x00000000 flash_type=nand [ 0.000000] PID hash table entries: 1024 (order: 0, 4096 bytes)[ 0.000000] Dentry cache hash table entries: 32768 (order: 5, 131072 bytes)[ 0.000000] Inode-cache hash table entries: 16384 (order: 4, 65536 bytes)[ 0.000000] Memory: 249928K/260096K available (4452K kernel code, 146K rwdata, 688K rodata, 1024K init, 236K bss, 10168K reserved, 0K cma-reserved, 0K highmem)[ 0.000000] Virtual kernel memory layout:[ 0.000000] vector : 0xffff0000 - 0xffff1000 ( 4 kB)[ 0.000000] fixmap : 0xffc00000 - 0xfff00000 (3072 kB)[ 0.000000] vmalloc : 0xd0800000 - 0xff800000 ( 752 MB)[ 0.000000] lowmem : 0xc0000000 - 0xd0000000 ( 256 MB)[ 0.000000] pkmap : 0xbfe00000 - 0xc0000000 ( 2 MB)[ 0.000000] modules : 0xbf000000 - 0xbfe00000 ( 14 MB)[ 0.000000] .text : 0xc0208000 - 0xc0759318 (5445 kB)[ 0.000000] .init : 0xc0900000 - 0xc0a00000 (1024 kB)[ 0.000000] .data : 0xc0a00000 - 0xc0a24b80 ( 147 kB)[ 0.000000] .bss : 0xc0a26000 - 0xc0a61018 ( 237 kB)[ 0.000000] SLUB: HWalign=64, Order=0-3, MinObjects=0, CPUs=4, Nodes=1[ 0.000000] Hierarchical RCU implementation.[ 0.000000] NR_IRQS: 16, nr_irqs: 16, preallocated irqs: 16[ 0.000000] arch_timer: cp15 timer(s) running at 48.00MHz (virt).[ 0.000000] clocksource: arch_sys_counter: mask: 0xffffffffffffff max_cycles: 0xb11fd3bfb, max_idle_ns: 440795203732 ns[ 0.000007] sched_clock: 56 bits at 48MHz, resolution 20ns, wraps every 4398046511096ns[ 0.000021] Switching to timer-based delay loop, resolution 20ns[ 0.000243] Calibrating delay loop (skipped), value calculated using timer frequency.. 96.00 BogoMIPS (lpj=480000)[ 0.000261] pid_max: default: 32768 minimum: 301[ 0.000394] Mount-cache hash table entries: 1024 (order: 0, 4096 bytes)[ 0.000412] Mountpoint-cache hash table entries: 1024 (order: 0, 4096 bytes)[ 0.001001] CPU: Testing write buffer coherency: ok[ 0.001670] Setting up static identity map for 0x80300000 - 0x80300060[ 0.001810] Hierarchical SRCU implementation.[ 0.002457] smp: Bringing up secondary CPUs ...[ 0.005139] smp: Brought up 1 node, 4 CPUs[ 0.005156] SMP: Total of 4 processors activated (384.00 BogoMIPS).[ 0.005164] CPU: All CPU(s) started in SVC mode.[ 0.009140] VFP support v0.3: implementor 41 architecture 2 part 30 variant 7 rev 5[ 0.009290] clocksource: jiffies: mask: 0xffffffff max_cycles: 0xffffffff, max_idle_ns: 19112604462750000 ns[ 0.009313] futex hash table entries: 1024 (order: 4, 65536 bytes)[ 0.009492] pinctrl core: initialized pinctrl subsystem[ 0.010405] NET: Registered protocol family 16[ 0.010688] DMA: preallocated 256 KiB pool for atomic coherent allocations[ 0.011684] cpuidle: using governor ladder[ 0.011727] cpuidle: using governor menu[ 0.028703] usbcore: registered new interface driver usbfs[ 0.028765] usbcore: registered new interface driver hub[ 0.028841] usbcore: registered new device driver usb[ 0.028887] pps_core: LinuxPPS API ver. 1 registered[ 0.028896] pps_core: Software ver. 5.3.6 - Copyright 2005-2007 Rodolfo Giometti <giometti@linux.it>[ 0.028920] PTP clock support registered[ 0.030135] clocksource: Switched to clocksource arch_sys_counter[ 0.030958] NET: Registered protocol family 2[ 0.031627] TCP established hash table entries: 2048 (order: 1, 8192 bytes)[ 0.031670] TCP bind hash table entries: 2048 (order: 2, 16384 bytes)[ 0.031719] TCP: Hash tables configured (established 2048 bind 2048)[ 0.031826] UDP hash table entries: 256 (order: 1, 8192 bytes)[ 0.031860] UDP-Lite hash table entries: 256 (order: 1, 8192 bytes)[ 0.032045] NET: Registered protocol family 1[ 0.032090] PCI: CLS 0 bytes, default 64[ 0.033025] No memory allocated for crashlog[ 0.033203] workingset: timestamp_bits=30 max_order=16 bucket_order=0[ 0.036549] squashfs: version 4.0 (2009/01/31) Phillip Lougher[ 0.036563] jffs2: version 2.2 (NAND) (SUMMARY) (LZMA) (RTIME) (CMODE_PRIORITY) (c) 2001-2006 Red Hat, Inc.[ 0.041808] io scheduler noop registered[ 0.041827] io scheduler deadline registered (default)[ 0.043230] OF: PCI: host bridge /soc/pci@40000000 ranges:[ 0.043265] OF: PCI: IO 0x40200000..0x402fffff -> 0x40200000[ 0.043282] OF: PCI: MEM 0x40300000..0x40ffffff -> 0x40300000[ 0.260125] qcom-pcie 40000000.pci: link up[ 0.260276] qcom-pcie 40000000.pci: PCI host bridge to bus 0000:00[ 0.260296] pci_bus 0000:00: root bus resource [bus 00-ff][ 0.260312] pci_bus 0000:00: root bus resource [io 0x0000-0xfffff] (bus address [0x40200000-0x402fffff])[ 0.260326] pci_bus 0000:00: root bus resource [mem 0x40300000-0x40ffffff][ 0.260368] pci 0000:00:00.0: [17cb:1001] type 01 class 0x060400[ 0.260404] pci 0000:00:00.0: reg 0x10: [mem 0x00000000-0x00000fff 64bit][ 0.260462] pci 0000:00:00.0: PME# supported from D0 D3hot[ 0.260657] PCI: bus0: Fast back to back transfers disabled[ 0.260870] pci 0000:01:00.0: [168c:0056] type 00 class 0x028000[ 0.261078] pci 0000:01:00.0: reg 0x10: [mem 0x00000000-0x001fffff 64bit][ 0.261742] pci 0000:01:00.0: PME# supported from D0 D3hot[ 0.262028] PCI: bus1: Fast back to back transfers disabled[ 0.262080] pci 0000:00:00.0: BAR 8: assigned [mem 0x40400000-0x405fffff][ 0.262097] pci 0000:00:00.0: BAR 0: assigned [mem 0x40300000-0x40300fff 64bit][ 0.262121] pci 0000:01:00.0: BAR 0: assigned [mem 0x40400000-0x405fffff 64bit][ 0.262197] pci 0000:00:00.0: PCI bridge to [bus 01-ff][ 0.262213] pci 0000:00:00.0: bridge window [mem 0x40400000-0x405fffff][ 0.262944] pcieport 0000:00:00.0: AER enabled with IRQ 94[ 0.264380] bam-dma-engine 8e04000.dma: num-channels unspecified in dt[ 0.264396] bam-dma-engine 8e04000.dma: num-ees unspecified in dt[ 0.265600] tcsr 1949000.tcsr: setting wifi_glb_cfg = 41000000[ 0.265689] tcsr 1953000.ess_tcsr: setting ess interface select = 0[ 0.265764] tcsr 1957000.tcsr: setting wifi_noc_memtype_m0_m2 = 2222222[ 0.265991] Serial: 8250/16550 driver, 16 ports, IRQ sharing enabled[ 0.267723] msm_serial 78af000.serial: msm_serial: detected port #0[ 0.267769] msm_serial 78af000.serial: uartclk = 1843200[ 0.267821] 78af000.serial: ttyMSM0 at MMIO 0x78af000 (irq = 25, base_baud = 115200) is a MSM[ 0.267848] msm_serial: console setup on port #0[ 0.868129] console [ttyMSM0] enabled[ 0.873013] msm_serial: driver initialized[ 0.880444] loop: module loaded[ 0.881971] nand: device found, Manufacturer ID: 0xc2, Chip ID: 0xf1[ 0.883373] nand: Macronix MX30LF1G18AC[ 0.889969] nand: 128 MiB, SLC, erase size: 128 KiB, page size: 2048, OOB size: 64[ 0.893639] 7 fixed-partitions partitions found on MTD device qcom_nand.0[ 0.901189] Creating 7 MTD partitions on "qcom_nand.0":[ 0.908032] 0x000000000000-0x000000080000 : "SBL1"[ 0.914114] 0x000000080000-0x000000100000 : "MIBIB"[ 0.918894] 0x000000100000-0x000000200000 : "QSEE"[ 0.924060] 0x000000200000-0x000000280000 : "CDT"[ 0.928486] 0x000000280000-0x0000003c0000 : "APPSBL"[ 0.933886] 0x0000003c0000-0x000000400000 : "APPSBLENV"[ 0.938105] 0x000000400000-0x000008000000 : "ubi"[ 0.951087] random: fast init done[ 1.035399] libphy: ipq40xx_mdio: probed[ 1.066132] ESS reset ok![ 1.099109] ESS reset ok![ 1.364121] PHY 3 single test PSGMII issue happen![ 1.506710] PHY3 test see issue![ 1.534776] ESS reset ok![ 1.960494] libphy: Fixed MDIO Bus: probed[ 1.961377] EDMA using MAC@ - using[ 1.961391] 92:46:9c:XX:XX:XX[ 1.967562] EDMA using MAC@ - using[ 1.967573] 5e:c8:13:XX:XX:XX[ 2.071090] i2c /dev entries driver[ 2.071348] i2c_qup 78b7000.i2c: using default clock-frequency 100000[ 2.200570] lp5523x 0-0032: lp5523 Programmable led chip found[ 2.225291] NET: Registered protocol family 10[ 2.227178] Segment Routing with IPv6[ 2.228735] NET: Registered protocol family 17[ 2.232482] bridge: filtering via arp/ip/ip6tables is no longer available by default. Update your scripts to load br_netfilter if you need this.[ 2.237092] 8021q: 802.1Q VLAN Support v1.8[ 2.249965] Registering SWP/SWPB emulation handler[ 2.258298] UBI: auto-attach mtd6[ 2.258585] ubi0: attaching mtd6[ 2.821444] random: crng init done[ 2.860717] ubi0: scanning is finished[ 2.868810] ubi0: attached mtd6 (name "ubi", size 124 MiB)[ 2.868843] ubi0: PEB size: 131072 bytes (128 KiB), LEB size: 126976 bytes[ 2.873234] ubi0: min./max. I/O unit sizes: 2048/2048, sub-page size 2048[ 2.880050] ubi0: VID header offset: 2048 (aligned 2048), data offset: 4096[ 2.886925] ubi0: good PEBs: 991, bad PEBs: 1, corrupted PEBs: 0[ 2.893691] ubi0: user volume: 8, internal volumes: 1, max. volumes count: 128[ 2.899933] ubi0: max/mean erase counter: 144/77, WL threshold: 4096, image sequence number: 2108563064[ 2.906979] ubi0: available PEBs: 0, total reserved PEBs: 991, PEBs reserved for bad PEB handling: 19[ 2.916282] ubi0: background thread "ubi_bgt0d" started, PID 85[ 2.917239] block ubiblock0_6: created from ubi0:6(rootfs)[ 2.931368] ubiblock: device ubiblock0_6 (rootfs) set to be root filesystem[ 2.936913] hctosys: unable to open rtc device (rtc0)[ 2.948593] VFS: Mounted root (squashfs filesystem) readonly on device 254:0.[ 2.950234] Freeing unused kernel memory: 1024K[ 3.379615] init: Console is alive[ 3.379836] init: - watchdog -[ 4.106459] kmodloader: loading kernel modules from /etc/modules-boot.d/*[ 4.363111] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller[ 4.363174] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 1[ 4.367729] xhci-hcd xhci-hcd.0.auto: hcc params 0x0220f665 hci version 0x100 quirks 0x0000000002010010[ 4.375156] xhci-hcd xhci-hcd.0.auto: irq 129, io mem 0x06000000[ 4.385118] hub 1-0:1.0: USB hub found[ 4.390753] hub 1-0:1.0: 1 port detected[ 4.394530] xhci-hcd xhci-hcd.0.auto: xHCI Host Controller[ 4.398322] xhci-hcd xhci-hcd.0.auto: new USB bus registered, assigned bus number 2[ 4.403660] xhci-hcd xhci-hcd.0.auto: Host supports USB 3.0 SuperSpeed[ 4.412272] usb usb2: We don't know the algorithms for LPM for this host, disabling LPM.[ 4.418293] hub 2-0:1.0: USB hub found[ 4.426159] hub 2-0:1.0: config failed, hub doesn't have any ports! (err -19)[ 4.430983] kmodloader: done loading kernel modules from /etc/modules-boot.d/*[ 4.452055] init: - preinit -[ 4.760164] usb 1-1: new full-speed USB device number 2 using xhci-hcd[ 5.415017] IPv6: ADDRCONF(NETDEV_UP): eth1: link is not ready[ 5.416292] ess_edma c080000.edma: eth1: GMAC Link is up with phy_speed=100[ 5.419769] IPv6: ADDRCONF(NETDEV_CHANGE): eth1: link becomes ready[ 8.683184] UBIFS (ubi0:7): default file-system created[ 8.683903] UBIFS (ubi0:7): background thread "ubifs_bgt0_7" started, PID 198[ 8.737246] UBIFS (ubi0:7): UBIFS: mounted UBI device 0, volume 7, name "rootfs_data"[ 8.737284] UBIFS (ubi0:7): LEB size: 126976 bytes (124 KiB), min./max. I/O unit sizes: 2048 bytes/2048 bytes[ 8.744100] UBIFS (ubi0:7): FS size: 45457408 bytes (43 MiB, 358 LEBs), journal size 2285568 bytes (2 MiB, 18 LEBs)[ 8.753979] UBIFS (ubi0:7): reserved for root: 2147065 bytes (2096 KiB)[ 8.764211] UBIFS (ubi0:7): media format: w4/r0 (latest is w5/r0), UUID 7C6EXXXX-XXXX-XXXX-XXXX-XXXXXXXXXXXX, small LPT model[ 8.772497] mount_root: overlay filesystem has not been fully initialized yet[ 8.782670] mount_root: switching to ubifs overlay[ 8.804158] urandom-seed: Seed file not found (/etc/urandom.seed)[ 8.875324] procd: - early -[ 8.875427] procd: - watchdog -[ 9.671252] procd: - watchdog -[ 9.674148] procd: - ubus -[ 9.821384] procd: - init -[ 10.267489] kmodloader: loading kernel modules from /etc/modules.d/*[ 10.274415] ip6_tables: (C) 2000-2006 Netfilter Core Team[ 10.283392] hidraw: raw HID events driver (C) Jiri Kosina[ 10.290463] Bluetooth: Core ver 2.22[ 10.290559] NET: Registered protocol family 31[ 10.293103] Bluetooth: HCI device and connection manager initialized[ 10.297371] Bluetooth: HCI socket layer initialized[ 10.303641] urngd: v1.0.2 started.[ 10.303942] Bluetooth: L2CAP socket layer initialized[ 10.311992] Bluetooth: SCO socket layer initialized[ 10.318473] Bluetooth: BNEP (Ethernet Emulation) ver 1.3[ 10.321791] Bluetooth: BNEP filters: protocol multicast[ 10.327322] Bluetooth: BNEP socket layer initialized[ 10.334873] usbcore: registered new interface driver btusb[ 10.338327] Loading modules backported from Linux version v4.19.98-0-gd183c8e2647a[ 10.342865] Backport generated by backports.git v4.19.98-1-0-g8204eb99[ 10.352610] Bluetooth: HCI UART driver ver 2.3[ 10.356822] Bluetooth: HCI UART protocol H4 registered[ 10.361300] Bluetooth: HCI UART protocol BCSP registered[ 10.366368] Bluetooth: HCI UART protocol ATH3K registered[ 10.372961] Bluetooth: HIDP (Human Interface Emulation) ver 1.2[ 10.377229] Bluetooth: HIDP socket layer initialized[ 10.385036] ip_tables: (C) 2000-2006 Netfilter Core Team[ 10.393348] nf_conntrack version 0.5.0 (4096 buckets, 16384 max)[ 10.414862] Bluetooth: RFCOMM TTY layer initialized[ 10.414910] Bluetooth: RFCOMM socket layer initialized[ 10.418644] Bluetooth: RFCOMM ver 1.11[ 10.434119] xt_time: kernel timezone is -0000[ 10.434897] usbcore: registered new interface driver ath3k[ 10.464700] PPP generic driver version 2.4.2[ 10.465664] NET: Registered protocol family 24[ 10.479305] ath10k 4.19 driver, optimized for CT firmware, probing pci device: 0x56.[ 10.480093] ath10k_pci 0000:01:00.0: enabling device (0140 -> 0142)[ 10.486727] ath10k_pci 0000:01:00.0: pci irq msi oper_irq_mode 2 irq_mode 0 reset_mode 0[ 10.671786] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/fwcfg-pci-0000:01:00.0.txt failed with error -2[ 10.671828] ath10k_pci 0000:01:00.0: Falling back to user helper[ 10.750826] firmware ath10k!fwcfg-pci-0000:01:00.0.txt: firmware_loading_store: map pages failed[ 10.751198] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/pre-cal-pci-0000:01:00.0.bin failed with error -2[ 10.758698] ath10k_pci 0000:01:00.0: Falling back to user helper[ 10.912123] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA9888/hw2.0/ct-firmware-5.bin failed with error -2[ 10.912176] ath10k_pci 0000:01:00.0: Falling back to user helper[ 10.983813] firmware ath10k!QCA9888!hw2.0!ct-firmware-5.bin: firmware_loading_store: map pages failed[ 10.984200] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA9888/hw2.0/ct-firmware-2.bin failed with error -2[ 10.992085] ath10k_pci 0000:01:00.0: Falling back to user helper[ 11.057547] firmware ath10k!QCA9888!hw2.0!ct-firmware-2.bin: firmware_loading_store: map pages failed[ 11.057968] ath10k_pci 0000:01:00.0: Direct firmware load for ath10k/QCA9888/hw2.0/firmware-6.bin failed with error -2[ 11.065844] ath10k_pci 0000:01:00.0: Falling back to user helper[ 11.129819] firmware ath10k!QCA9888!hw2.0!firmware-6.bin: firmware_loading_store: map pages failed[ 11.390841] ath10k_pci 0000:01:00.0: qca9888 hw2.0 target 0x01000000 chip_id 0x00000000 sub 0000:0000[ 11.390887] ath10k_pci 0000:01:00.0: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0[ 11.402934] ath10k_pci 0000:01:00.0: firmware ver 10.4b-ct-9888-fW-012-17ba98334 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 a08ba414[ 11.764897] ath10k_pci 0000:01:00.0: board_file api 2 bmi_id 0:17 crc32 f228337a[ 13.797229] ath10k_pci 0000:01:00.0: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96[ 13.797271] ath10k_pci 0000:01:00.0: msdu-desc: 2500 skid: 32[ 13.830809] ath10k_pci 0000:01:00.0: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'[ 13.831851] ath10k_pci 0000:01:00.0: wmi print 'free: 117888 iram: 22644 sram: 26276'[ 13.998405] ath10k_pci 0000:01:00.0: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1[ 14.145258] ath: EEPROM regdomain: 0x0[ 14.145269] ath: EEPROM indicates default country code should be used[ 14.145274] ath: doing EEPROM country->regdmn map search[ 14.145284] ath: country maps to regdmn code: 0x3a[ 14.145292] ath: Country alpha2 being used: US[ 14.145297] ath: Regpair used: 0x3a[ 14.332452] ath10k_ahb a000000.wifi: Direct firmware load for ath10k/fwcfg-ahb-a000000.wifi.txt failed with error -2[ 14.332527] ath10k_ahb a000000.wifi: Falling back to user helper[ 14.902643] firmware ath10k!fwcfg-ahb-a000000.wifi.txt: firmware_loading_store: map pages failed[ 14.903026] ath10k_ahb a000000.wifi: Direct firmware load for ath10k/pre-cal-ahb-a000000.wifi.bin failed with error -2[ 14.910580] ath10k_ahb a000000.wifi: Falling back to user helper[ 15.059589] ath10k_ahb a000000.wifi: Direct firmware load for ath10k/QCA4019/hw1.0/ct-firmware-5.bin failed with error -2[ 15.059641] ath10k_ahb a000000.wifi: Falling back to user helper[ 15.118956] firmware ath10k!QCA4019!hw1.0!ct-firmware-5.bin: firmware_loading_store: map pages failed[ 15.119277] ath10k_ahb a000000.wifi: Direct firmware load for ath10k/QCA4019/hw1.0/ct-firmware-2.bin failed with error -2[ 15.127293] ath10k_ahb a000000.wifi: Falling back to user helper[ 15.196667] firmware ath10k!QCA4019!hw1.0!ct-firmware-2.bin: firmware_loading_store: map pages failed[ 15.197060] ath10k_ahb a000000.wifi: Direct firmware load for ath10k/QCA4019/hw1.0/firmware-6.bin failed with error -2[ 15.204970] ath10k_ahb a000000.wifi: Falling back to user helper[ 15.274352] firmware ath10k!QCA4019!hw1.0!firmware-6.bin: firmware_loading_store: map pages failed[ 15.517462] ath10k_ahb a000000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff sub 0000:0000[ 15.517507] ath10k_ahb a000000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0[ 15.529043] ath10k_ahb a000000.wifi: firmware ver 10.4b-ct-4019-fW-012-17ba98334 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 8f2e0e09[ 15.618475] ath10k_ahb a000000.wifi: board_file api 2 bmi_id 0:20 crc32 4329f4ee[ 16.927906] ath10k_ahb a000000.wifi: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96[ 16.927955] ath10k_ahb a000000.wifi: msdu-desc: 2500 skid: 32[ 16.962865] ath10k_ahb a000000.wifi: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'[ 16.963859] ath10k_ahb a000000.wifi: wmi print 'free: 56528 iram: 23400 sram: 32520'[ 17.076965] ath10k_ahb a000000.wifi: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1[ 17.313453] ath: EEPROM regdomain: 0x0[ 17.313462] ath: EEPROM indicates default country code should be used[ 17.313466] ath: doing EEPROM country->regdmn map search[ 17.313473] ath: country maps to regdmn code: 0x3a[ 17.313479] ath: Country alpha2 being used: US[ 17.313482] ath: Regpair used: 0x3a[ 17.492184] ath10k_ahb a800000.wifi: Direct firmware load for ath10k/fwcfg-ahb-a800000.wifi.txt failed with error -2[ 17.492245] ath10k_ahb a800000.wifi: Falling back to user helper[ 17.685408] firmware ath10k!fwcfg-ahb-a800000.wifi.txt: firmware_loading_store: map pages failed[ 17.685822] ath10k_ahb a800000.wifi: Direct firmware load for ath10k/pre-cal-ahb-a800000.wifi.bin failed with error -2[ 17.693392] ath10k_ahb a800000.wifi: Falling back to user helper[ 17.812964] ath10k_ahb a800000.wifi: Direct firmware load for ath10k/QCA4019/hw1.0/ct-firmware-5.bin failed with error -2[ 17.813008] ath10k_ahb a800000.wifi: Falling back to user helper[ 17.866598] firmware ath10k!QCA4019!hw1.0!ct-firmware-5.bin: firmware_loading_store: map pages failed[ 17.866944] ath10k_ahb a800000.wifi: Direct firmware load for ath10k/QCA4019/hw1.0/ct-firmware-2.bin failed with error -2[ 17.874904] ath10k_ahb a800000.wifi: Falling back to user helper[ 17.938738] firmware ath10k!QCA4019!hw1.0!ct-firmware-2.bin: firmware_loading_store: map pages failed[ 17.939020] ath10k_ahb a800000.wifi: Direct firmware load for ath10k/QCA4019/hw1.0/firmware-6.bin failed with error -2[ 17.947033] ath10k_ahb a800000.wifi: Falling back to user helper[ 18.008540] firmware ath10k!QCA4019!hw1.0!firmware-6.bin: firmware_loading_store: map pages failed[ 18.008846] ath10k_ahb a800000.wifi: qca4019 hw1.0 target 0x01000000 chip_id 0x003b00ff sub 0000:0000[ 18.016506] ath10k_ahb a800000.wifi: kconfig debug 0 debugfs 1 tracing 0 dfs 1 testmode 0[ 18.030748] ath10k_ahb a800000.wifi: firmware ver 10.4b-ct-4019-fW-012-17ba98334 api 5 features mfp,peer-flow-ctrl,txstatus-noack,wmi-10.x-CT,ratemask-CT,regdump-CT,txrate-CT,flush-all-CT,pingpong-CT,ch-regs-CT,nop-CT,set-special-CT,tx-rc-CT,cust-stats-CT,txrate2-CT,beacon-cb-CT,wmi-block-ack-CT,wmi-bcn-rc-CT crc32 8f2e0e09[ 18.081285] ath10k_ahb a800000.wifi: board_file api 2 bmi_id 0:21 crc32 4329f4ee[ 19.390338] ath10k_ahb a800000.wifi: 10.4 wmi init: vdevs: 16 peers: 48 tid: 96[ 19.390379] ath10k_ahb a800000.wifi: msdu-desc: 2500 skid: 32[ 19.439090] ath10k_ahb a800000.wifi: wmi print 'P 48/48 V 16 K 144 PH 176 T 186 msdu-desc: 2500 sw-crypt: 0 ct-sta: 0'[ 19.441105] ath10k_ahb a800000.wifi: wmi print 'free: 56528 iram: 23400 sram: 32520'[ 19.555755] ath10k_ahb a800000.wifi: htt-ver 2.2 wmi-op 6 htt-op 4 cal pre-cal-file max-sta 32 raw 0 hwcrypto 1[ 19.675935] ath: EEPROM regdomain: 0x0[ 19.675947] ath: EEPROM indicates default country code should be used[ 19.675952] ath: doing EEPROM country->regdmn map search[ 19.675962] ath: country maps to regdmn code: 0x3a[ 19.675969] ath: Country alpha2 being used: US[ 19.675974] ath: Regpair used: 0x3a[ 19.685101] kmodloader: done loading kernel modules from /etc/modules.d/*[ 44.611931] ess_edma c080000.edma: eth1: GMAC Link is up with phy_speed=100[ 44.612750] br-lan: port 1(eth1) entered blocking state[ 44.617706] br-lan: port 1(eth1) entered disabled state[ 44.623341] device eth1 entered promiscuous mode[ 44.630394] br-lan: port 1(eth1) entered blocking state[ 44.633013] br-lan: port 1(eth1) entered forwarding state[ 44.638188] IPv6: ADDRCONF(NETDEV_UP): br-lan: link is not ready[ 44.655401] IPv6: ADDRCONF(NETDEV_UP): eth0: link is not ready[ 45.689956] IPv6: ADDRCONF(NETDEV_CHANGE): br-lan: link becomes ready[ 45.691600] IPv6: ADDRCONF(NETDEV_CHANGE): eth0: link becomes ready